Service interval resetting on VW
GOLF V
Serviceanzeige rücksetzen bei neuen VW Crafter / MB Sprinter
Service interval aanduiding terugstellen bij VW Crafter
Service
interval resetting on new VW Crafter / MB Sprinter
MB Sprinter & VW Crafter service reset Sitting in
the drivers seat looking at the dash on the left hand side you have a M button
and below it a 0 button these are the buttons you will need to use.
When i refer to the LCD this is the illuminated part
in the middle that shows your mileage, service mileage and trip mileage.
Please read this fully first to get the jist of it as
if you perform the actions too slow it wont work and
you will have to start over.
1.Put on ignition
2.Wait for service mileage to revert to vehicle mileage
3.When it reverts to the vehicle mileage press and hold the 0 button until you
hear a beep (can take up to 30 seconds)
4.As soon as you hear the beep press the M button repeatdly
and you will see in the LCD display different reset's
the one you need to select is "reset 51" if you go past it just keep
pressing the M button till it comes up again.
5.When the "reset 51" is displayed stop pressing the M button then
press and hold the 0 button again until a number 2 is displayed in the LCD.
6.Release the 0 button and then press twice and it
will say in the LCD reset done ,if it is not reset you will get a 30% power
reduction after 2K miles
Serviceanzeige
rücksetzen bei neuen
VW Crafter / MB Sprinter
Auf
der linken Seite des Schalttafeleinsatzes
sollten zwei Knöpfe zu finden sein,
M und 0 auf diese bezieht sich
nachfolgende Anleitung. Bitte lesen Sie
diese Anleitung vollständig bevor Sie die einzelnen Schritte durchführen.
1. Zündung einschalten
2. Warten Sie bis die Servicemeldung verschwindet und die normale Laufleistung des Fahrzeuges angezeigt wird.
3. Dürcken und halten sie nun den Knopf
0 solange bis ein Piepton zuhören ist, dies kann bis zu 30 Sekunden dauern.
4. Sobald Sie den Piepton hören drücken Sie
den Knopf M mehrfach. Im Display erscheinen nun die einzelnen Rücksetzungsmöglichkeiten, stoppen Sie
bei "Reset 51". Sollten
Sie diesen Punkt übersprungen haben betätigen sie den Knopf M erneut bis der entsprechende Punkt angezeigt wird.
5. Mit "Reset 51" im Display drücken und halten Sie nun den Knopf
0 bis die Zahl 2 im Display
erscheint.
6. Drücken Sie nun zweimal den Knopf 0, im Display sollte nun "Reset Done" angezeigt werden. Sollten Sie dies
nicht tun wird die Leistung des Fahrzeuges nach 2000 Meilen begrenzt.
Service interval aanduiding terugstellen bij VW Crafter
1. Als je in de
bestuurdersstoel zit en je kijkt naar de linkerkant van het dashboard, dan zie
je daar een M knop en daaronder een O knop. Deze twee knoppen heb je nodig.
2. Als naar de LCD wordt
verwezen, dan wordt het verlichte gedeelte in het midden bedoeld waar de
kilometerstand, service km en trip afstand getoond worden.
3. Contact aan.
4. Wacht totdat service mileage (afstand tot volgende service) vervangen
wordt door afgelegde afstand van de auto.
5. Wanneer de afgelegde
afstand van de auto is verschenen, druk dan op de O knop en houd die ingedrukt
totdat je een piep hoort en laat die knop dan los, (het kan wel 30 seconden
duren voordat je die piep hoort)
6. Zodra je de piep hoort druk
dan meerdere malen op de M knop; je ziet dan in het LCD display allerlei resets voorbij komen; wat jij nodig hebt is 'reset 51'; als je er per ongeluk voorbij bent, blijf dan
herhaald op de M knop drukken totdat 'reset 51' voor
je neus staat.
7. Als 'reset
51' in het display staat, laat dan de M knop los en
houdt de O knop ingedrukt totdat het cijfer 2 wordt weergegeven in het
display.8.
Laat de O knop dan los en druk
er dan nog 2x op; in het LCD display verschijnt nu 'reset
done'; als het niet gereset
is dan krijg je 30% verlies van vermogen na 2000 kilometer.
Service interval resetting on VW
GOLF V
Vehicles with Multifunction Display –
1.) With the key out of the ignition – Press and hold the “0.0”, located on the
right side of the instrument cluster.
2.) While holding the reset button insert the key and turn to the “Accessory”
position. Wait for “Service now!” message to appear on multi–functionscreen.
3.) Then release the “0.0” and press the “m” (minutes) button on the opposite
side of the instrument cluster.
4.) To verify it’s been reset hold the ”0.0″
button again – the display should indicate the future service by the message:
“Service in 5,000 mi / 8,000 KM or 180 days or 10,000 mi / 16,000 km or 365
days” depending on Service Interval adaptation.
Vehicles without Multifunction Display –
1.) With the key out of the ignition – Press and hold the “0.0”, located on the
right side of the instrument cluster.
2.) While holding the ”0.0″ button insert
the key and turn to the “Accessory” position. Wait for “wrench” symbol to
appear in the odometer display.
3.) Then release the “0.0” and press the “MIN” button on the opposite side of
the instrument cluster.
4.) To verify it’s been reset hold the ”0.0″
button again: The “wrench” symbol will appear together with the reset number of
miles / kilometers you can drive until the service
due date. The display changes after about 10 seconds. A “clock” symbol appears
together with the reset number of days until the service due date.