P0400 Exhaust Gas Recirculation Flow
Malfunction
P0401 Exhaust Gas Recirculation Flow
Insufficient Detected
P0402 Exhaust Gas Recirculation Flow
Excessive Detected
P0403 Exhaust Gas Recirculation Circuit
Malfunction
P0404 Exhaust Gas Recirculation Circuit
Range/Performance
P0405 Exhaust Gas Recirculation Sensor A
Circuit Low
P0406 Exhaust Gas Recirculation Sensor A
Circuit High
P0407 Exhaust Gas Recirculation Sensor B
Circuit Low
P0408 Exhaust Gas Recirculation Sensor B
Circuit High
P0410 Secondary Air Injection System
Malfunction
P0411 Secondary Air Injection System
Incorrect Flow Detected
P0412 Secondary Air Injection System
Switching Valve A Circuit Malfunction
P0413 Secondary Air Injection System
Switching Valve A Circuit Open
P0414 Secondary Air Injection System
Switching Valve A Circuit Shorted
P0415 Secondary Air Injection System
Switching Valve B Circuit Malfunction
P0416 Secondary Air Injection System
Switching Valve B Circuit Open
P0417 Secondary Air Injection System
Switching Valve B Circuit Shorted
P0418 Secondary Air Injection System
Relay "A" Circuit Malfunction
P0419 Secondary Air Injection System
Relay "B" Circuit Malfunction
P0420 Catalyst System Efficiency Below
Threshold (Bank 1)
P0421 Warm Up Catalyst Efficiency Below
Threshold (Bank 1)
P0422 Main Catalyst Efficiency Below
Threshold (Bank 1)
P0423 Heated Catalyst Efficiency Below
Threshold (Bank 1)
P0424 Heated Catalyst Temperature Below
Threshold (Bank 1)
P0430 Catalyst System Efficiency Below
Threshold (Bank 2)
P0431 Warm Up Catalyst Efficiency Below
Threshold (Bank 2)
P0432 Main Catalyst Efficiency Below
Threshold (Bank 2)
P0433 Heated Catalyst Efficiency Below
Threshold (Bank 2)
P0434 Heated Catalyst Temperature Below
Threshold (Bank 2)
P0440 Evaporative Emission Control
System Malfunction
P0441 Evaporative Emission Control
System Incorrect Purge Flow
P0442 Evaporative Emission Control
System Leak Detected (small leak)
P0443 Evaporative Emission Control
System Purge Control Valve Circuit
Malfunction
P0444 Evaporative Emission Control
System Purge Control Valve Circuit Open
P0445 Evaporative Emission Control
System Purge Control Valve Circuit
Shorted
P0446 Evaporative Emission Control
System Vent Control Circuit Malfunction
P0447 Evaporative Emission Control
System Vent Control Circuit Open
P0448 Evaporative Emission Control
System Vent Control Circuit Shorted
P0449 Evaporative Emission Control
System Vent Valve/Solenoid Circuit
Malfunction
P0450 Evaporative Emission Control
System Pressure Sensor Malfunction
P0451 Evaporative Emission Control
System Pressure Sensor Range/Performance
P0452 Evaporative Emission Control
System Pressure Sensor Low Input
P0453 Evaporative Emission Control
System Pressure Sensor High Input
P0454 Evaporative Emission Control
System Pressure Sensor Intermittent
P0455 Evaporative Emission Control
System Leak Detected (gross leak)
P0460 Fuel Level Sensor Circuit
Malfunction
P0461 Fuel Level Sensor Circuit
Range/Performance
P0462 Fuel Level Sensor Circuit Low
Input
P0463 Fuel Level Sensor Circuit High
Input
P0464 Fuel Level Sensor Circuit
Intermittent
P0465 Purge Flow Sensor Circuit
Malfunction
P0466 Purge Flow Sensor Circuit
Range/Performance
P0467 Purge Flow Sensor Circuit Low
Input
P0468 Purge Flow Sensor Circuit High
Input
P0469 Purge Flow Sensor Circuit
Intermittent
P0470 Exhaust Pressure Sensor
Malfunction
P0471 Exhaust Pressure Sensor
Range/Performance
P0472 Exhaust Pressure Sensor Low
P0473 Exhaust Pressure Sensor High
P0474 Exhaust Pressure Sensor
Intermittent
P0475 Exhaust Pressure Control Valve
Malfunction
P0476 Exhaust Pressure Control Valve
Range/Performance
P0477 Exhaust Pressure Control Valve Low
P0478 Exhaust Pressure Control Valve
High
P0479 Exhaust Pressure Control Valve
Intermittent
P0480 Cooling Fan 1 Control Circuit
Malfunction
P0481 Cooling Fan 2 Control Circuit
Malfunction
P0482 Cooling Fan 3 Control Circuit
Malfunction
P0483 Cooling Fan Rationality Check
Malfunction
P0484 Cooling Fan Circuit Over Current
P0485 Cooling Fan Power/Ground Circuit
Malfunction
P0500 Vehicle Speed Sensor Malfunction
P0501 Vehicle Speed Sensor
Range/Performance
P0502 Vehicle Speed Sensor Low Input
P0503 Vehicle Speed Sensor Intermittent/Erratic/High
P0505 Idle Control System Malfunction
P0506 Idle Control System RPM Lower Than
Expected
P0507 Idle Control System RPM Higher
Than Expected
P0510 Closed Throttle Position Switch
Malfunction
P0520 Engine Oil Pressure Sensor/Switch
Circuit Malfunction
P0521 Engine Oil Pressure Sensor/Switch
Circuit Range/Performance
P0522 Engine Oil Pressure Sensor/Switch
Circuit Low Voltage
P0523 Engine Oil Pressure Sensor/Switch
Circuit High Voltage
P0530 A/C Refrigerant Pressure Sensor
Circuit Malfunction
P0531 A/C Refrigerant Pressure Sensor
Circuit Range/Performance
P0532 A/C Refrigerant Pressure Sensor
Circuit Low Input
P0533 A/C Refrigerant Pressure Sensor
Circuit High Input
P0534 Air Conditioner Refrigerant Charge
Loss
P0550 Power Steering Pressure Sensor
Circuit Malfunction
P0551 Power Steering Pressure Sensor
Circuit Range/Performance
P0552 Power Steering Pressure Sensor
Circuit Low Input
P0553 Power Steering Pressure Sensor
Circuit High Input
P0554 Power Steering Pressure Sensor
Circuit Intermittent
P0560 System Voltage Malfunction
P0561 System Voltage Unstable
P0562 System Voltage Low
P0563 System Voltage High
P0565 Cruise Control On Signal
Malfunction
P0566 Cruise Control Off Signal
Malfunction
P0567 Cruise Control Resume Signal
Malfunction
P0568 Cruise Control Set Signal
Malfunction
P0569 Cruise Control Coast Signal
Malfunction
P0570 Cruise Control Accel Signal
Malfunction
P0571 Cruise Control/Brake Switch A
Circuit Malfunction
P0572 Cruise Control/Brake Switch A
Circuit Low
P0573 Cruise Control/Brake Switch A
Circuit High
P0574 Cruise Control Related Malfunction
P0575 Cruise Control Related Malfunction
P0576 Cruise Control Related Malfunction
P0576 Cruise Control Related Malfunction
P0578 Cruise Control Related Malfunction
P0579 Cruise Control Related Malfunction
P0580 Cruise Control Related Malfunction
P0600 Serial Communication Link
Malfunction
P0601 Internal Control Module Memory
Check Sum Error
P0602 Control Module Programming Error
P0603 Internal Control Module Keep Alive
Memory (KAM) Error
P0604 Internal Control Module Random
Access Memory (RAM) Error
P0605 Internal Control Module Read Only
Memory (ROM) Error
P0606 PCM Processor Fault
P0608 Control Module VSS Output "A"
Malfunction
P0609 Control Module VSS Output "B"
Malfunction
P0620 Generator Control Circuit
Malfunction
P0621 Generator Lamp "L" Control Circuit
Malfunction
P0622 Generator Field "F" Control
Circuit Malfunction
P0650 Malfunction Indicator Lamp (MIL)
Control Circuit Malfunction
P0654 Engine RPM Output Circuit
Malfunction
P0655 Engine Hot Lamp Output Control
Circuit Malfucntion
P0656 Fuel Level Output Circuit
Malfunction
P0700 Transmission Control System
Malfunction
P0701 Transmission Control System
Range/Performance
P0702 Transmission Control System
Electrical
P0703 Torque Converter/Brake Switch B
Circuit Malfunction
P0704 Clutch Switch Input Circuit
Malfunction
P0705 Transmission Range Sensor Circuit
malfunction (PRNDL Input)
P0706 Transmission Range Sensor Circuit
Range/Performance
P0707 Transmission Range Sensor Circuit
Low Input
P0708 Transmission Range Sensor Circuit
High Input
P0709 Transmission Range Sensor Circuit
Intermittent
P0710 Transmission Fluid Temperature
Sensor Circuit Malfunction
P0711 Transmission Fluid Temperature
Sensor Circuit Range/Performance
P0712 Transmission Fluid Temperature
Sensor Circuit Low Input
P0713 Transmission Fluid Temperature
Sensor Circuit High Input
P0714 Transmission Fluid Temperature
Sensor Circuit Intermittent
P0715 Input/Turbine Speed Sensor Circuit
Malfunction
P0716 Input/Turbine Speed Sensor Circuit
Range/Performance
P0717 Input/Turbine Speed Sensor Circuit
No Signal
P0718 Input/Turbine Speed Sensor Circuit
Intermittent
P0719 Torque Converter/Brake Switch B
Circuit Low
P0720 Output Speed Sensor Circuit
Malfunction
P0721 Output Speed Sensor
Range/Performance
P0722 Output Speed Sensor No Signal
P0723 Output Speed Sensor Intermittent
P0724 Torque Converter/Brake Switch B
Circuit High
P0725 Engine Speed input Circuit
Malfunction
P0726 Engine Speed Input Circuit
Range/Performance
P0727 Engine Speed Input Circuit No
Signal
P0728 Engine Speed Input Circuit
Intermittent
P0730 Incorrect Gear Ratio
P0731 Gear 1 Incorrect ratio
P0732 Gear 2 Incorrect ratio
P0733 Gear 3 Incorrect ratio
P0734 Gear 4 Incorrect ratio
P0735 Gear 5 Incorrect ratio
P0736 Reverse incorrect gear ratio
P0740 Torque Converter Clutch Circuit
Malfuction
P0741 Torque Converter Clutch Circuit
Performance or Stuck Off
P0742 Torque Converter Clutch Circuit
Stuck On
P0743 Torque Converter Clutch Circuit
Electrical
P0744 Torque Converter Clutch Circuit
Intermittent
P0745 Pressure Control Solenoid
Malfunction
P0746 Pressure Control Solenoid
Performance or Stuck Off
P0747 Pressure Control Solenoid Stuck On
P0748 Pressure Control Solenoid
Electrical
P0749 Pressure Control Solenoid
Intermittent
P0750 Shift Solenoid A Malfunction
P0751 Shift Solenoid A Performance or
Stuck Off
P0752 Shift Solenoid A Stuck On
P0753 Shift Solenoid A Electrical
P0754 Shift Solenoid A Intermittent
P0755 Shift Solenoid B Malfunction
P0756 Shift Solenoid B Performance or
Stuck Off
P0757 Shift Solenoid B Stuck On
P0758 Shift Solenoid B Electrical
P0759 Shift Solenoid B Intermittent
P0760 Shift Solenoid C Malfunction
P0761 Shift Solenoid C Performance or
Stuck Off
P0762 Shift Solenoid C Stuck On
P0763 Shift Solenoid C Electrical
P0764 Shift Solenoid C Intermittent
P0765 Shift Solenoid D Malfunction
P0766 Shift Solenoid D Performance or
Stuck Off
P0767 Shift Solenoid D Stuck On
P0768 Shift Solenoid D Electrical
P0769 Shift Solenoid D Intermittent
P0770 Shift Solenoid E Malfunction
P0771 Shift Solenoid E Performance or
Stuck Off
P0772 Shift Solenoid E Stuck On
P0773 Shift Solenoid E Electrical
P0774 Shift Solenoid E Intermittent
P0780 Shift Malfunction
P0781 1-2 Shift Malfunction
P0782 2-3 Shift Malfunction
P0783 3-4 Shift Malfunction
P0784 4-5 Shift Malfunction
P0785 Shift/Timing Solenoid Malfunction
P0786 Shift/Timing Solenoid
Range/Performance
P0787 Shift/Timing Solenoid Low
P0788 Shift/Timing Solenoid High
P0789 Shift/Timing Solenoid Intermittent
P0790 Normal/Performance Switch Circuit
Malfunction
P0801 Reverse Inhibit Control Circuit
Malfunction
P0803 1-4 Upshift (Skip Shift) Solenoid
Control Circuit Malfunction
P0804 1-4 Upshift (Skip Shift) Lamp
Control Circuit Malfunction
P0805 Clutch Position Sensor Circuit
Malfunction
P0806 Clutch Position Sensor Circuit
Range/Performance
P0807 Clutch Position Sensor Circuit Low
P0808 Clutch Position Sensor Circuit
High
P0809 Clutch Position Sensor Circuit
Intermittent Ckt
P0810 Clutch Position Control
Malfunction
P0811 Clutch Slippage Excessive
P0812 Reverse Input Circuit Malfunction
P0813 Reverse Output Circuit Malfunction
P0814 Trans Range Display Circuit
Malfunction
P0815 Upshift Switch Circuit Malfunction
P0816 Downshift Switch Circuit
Malfunction
P0817 Starter Disable Circuit
P0818 Driveline Disconn. Switch Input
P0820 Gear Lever X-Y Sensor Circuit
P0821 Gear Lever X Sensor Circuit
P0822 Gear Lever Y Sensor Circuit
P0823 Gear Lever X Sensor Circuit
Intermittent Ckt
P0824 Gear Lever Y Sensor Circuit
Intermittent Ckt
P0830 Clutch Position Switch A Circuit
Malfunction
P0831 Clutch Position Switch A Circuit
Low
P0832 Clutch Position Switch A Circuit
High
P0833 Clutch Position Switch B Circuit
Malfunction
P0834 Clutch Position Switch B Circuit
Low
P0835 Clutch Position Switch B Circuit
High
P0836 4 Wheel Drive Switch Circuit
Malfunction
P0837 4 Wheel Drive Switch CKT Range/Perf
P0838 4 Wheel Drive Switch Circuit Low
P0839 4 Wheel Drive Switch Circuit High
P0840 Trans Fluid Press Sensor/Switch A
Circuit Malfunction
P0841 Trans Fluid Press Sensor/Switch A
CKT Range/Perf
P0842 Trans Fluid Press Sensor/Switch A
Circuit Low
P0843 Trans Fluid Press Sensor/Switch A
Circuit High
P0844 Trans Fluid Press Sensor/Switch A
CKT Intermittent
P0845 Trans Fluid Press Sensor/Switch B
Circuit Malfunction
P0846 Trans Fluid Press Sensor/Switch B
CKT Range/Perf
P0847 Trans Fluid Press Sensor/Switch B
Circuit Low
P0848 Trans Fluid Press Sensor/Switch B
Circuit High
P0849 Trans Fluid Press Sensor/Switch B
CKT Intermittent
P1000 Electronic Gear Selector Module:
Defective N15/5
P1031 component G3/3 (O2-in CAT front
left detector) and G3/4 (O2-in CAT front
right detector) exchange
P1032 O2 sensors upstream TWC mixed up
G3/3,G3/4
P1105 Altitude pressure sensor control
module
P1105 Atmospheric pressure sensor
Readout too large.
P1105 Atmospheric pressure sensor
Readout too small.
P1105 high pressure sensor controller
P1146 left HF type AFM sensor (B2/6)
P1147 left coolant temperature sensor
(B11/9)
P1148 left intake air temperature sensor
(B17/5)
P1149 left pressure sensor (B28/1)
P1162 left regulation part practical
potentiometer
P1163 engine oil condition control
switch (S43)
P1163 Oil sensor:engine oil level
implausible (B10)
P1176 engine oil sensor (B40)
P1176 Oil pressure sensor malfunction
(B10)
P1177 engine oil sensor (B40) engine oil
temperature error
P1177 Oil sensor:engine oil temperature
implausible (B10)
P1178 engine oil sensor (B40) engine oil
condition error
P1178 Oil sensor:engine oil level
implausible (B10)
P1179 engine oil sensor (B40) engine oil
quality error
P1179 Oil sensor:engine oil quality
implausible (B10)
P1180 engine oil sensor (B40) engine oil
temperature too high
P1180 Oil sensor:engine oil temperature
too high (B10)
P1181 Electric induction fan Engine/AC
malfunction (M34)
P1181 engine/A/C electronic suction
device (M4/3) rating RPM error
P1183 Malfunction right cylinder
shut-off output stage
P1184 Malfunction left cylinder shut-off
output stage
P1185 engine oil sensor (B40) water in
engine oil
P1185 Oil sensor:water in engine oil
(B10)
P1186 Safety fuel shut-off
P1187 fuel rail pressure inspection
P1187 Rail pressure monitoring Control
variation < 1500/min (rpm)
P1187 Rail pressure monitoring Control
variation < 1500/min (rpm)
P1187 Rail pressure monitoring Control
variation > 1500/min (rpm)
P1187 Rail pressure monitoring Control
variation > 1500/min (rpm)
P1187 Rail pressure monitoring Leakage
P1187 Rail pressure monitoring Leakage
P1187 Rail pressure monitoring The
maximum pressure has been exceeded.
P1187 Rail pressure monitoring The
maximum pressure has been exceeded.
P1187 Rail pressure monitoring The
pressure control valve jams in the
closed position.
P1187 Rail pressure monitoring The
pressure control valve jams in the
closed position.
P1187 Rail pressure monitoring The rail
pressure cannot be built up.
P1187 Rail pressure monitoring The rail
pressure cannot be built up.
P1187 Rail pressure monitoring The rail
pressure is too low.
P1187 Rail pressure monitoring The rail
pressure is too low.
P1189 Inlet port shutoff M55 (Inlet port
shutoff motor)
P1189 Inlet port shutoff Open circuit
P1189 Inlet port shutoff Short circuit
P1189 Inlet port shutoff The flaps jam
in the closed position.
P1189 Inlet port shutoff The flaps jam
in the open position.
P1189 intake air turnoff switch valve
Y83
P1190 Fuel pressure control valve N3/9 (CDI
control module)
P1190 Fuel pressure control valve Open
circuit
P1190 Fuel pressure control valve Short
circuit
P1190 fuel pressure regulation valve Y74
P1192 B40 (Oil sensor (oil level,temperature
and quality)) Oil level is implausible.
P1192 B40 (Oil sensor (oil level,temperature
and quality)) Oil quality is implausible.
P1192 B40 (Oil sensor (oil level,temperature
and quality)) Oil temperature is
implausible.
P1192 B40 (Oil sensor (oil level,temperature
and quality)) Period error of oil sensor
P1192 B40 (Oil sensor (oil level,temperature
and quality)) Short circuit/Open circuit
P1192 B40 (Oil sensor (oil level,temperature
and quality)) Synchronization pause is
breached.
P1192 B40 (Oil sensor (oil level,temperature
and quality)) The supply voltage is too
high or too low.
P1192 B40 (Oil sensor (oil level,temperature
and quality)) Water in engine oil P1192
engine oil sensor B40
P1220 Fuel metering control Y23/1
P1221 CAN communication if faulty.Fault
of ETC over CAN
P1221 CAN communication is faulty.Fault
of traction system over CAN
P1221 CAN reception from ASR/ETC/ESP
P1221 CAN signal from ASR/EGS/ESP
P1222 accelerator pedal position sensor
B37
P1222 B37 (Pedal value sensor) Sensor 1
Plausibility 1
P1222 B37 (Pedal value sensor) Sensor 1
Plausibility 2
P1222 B37 (Pedal value sensor) Sensor 1
Plausibility 3
p1222 B37 (Pedal value sensor) Sensor 1
The signal voltage is too high.
p1222 B37 (Pedal value sensor) Sensor 1
The signal voltage is too low.
p1222 B37 (Pedal value sensor) Sensor 1
The supply voltage is too high or too
low.
P1222 Potentiometer R25/2
P1223 Distributer shaft position sensor
Y23/2|2
P1223 Fuel rack travel sensor or slide
valve position sensor Y23/11
P1224 Fuel metering control
P1225 Intake pressure control
P1225 Resonance intake manifold
switchover valve (Y77)
P1226 Cam ring position sensor Y23/2|1
P1227 Distributer shaft position sensor
Y23/2|2
P1228 Injection pump quantity stop
P1229 Balancing resistor Y23/2r2
P1230 Cam ring position sensor Y23/2|1
P1233 Throttle valve actuator jamming (iced
up) M16/6
P1234 accelerator pedal position sensor
B37
P1234 B37 (Pedal value sensor) Sensor 2
IMPLAUSIBLE Sensor 1/2
P1234 B37 (Pedal value sensor) Sensor 2
The signal voltage is too high.
P1234 B37 (Pedal value sensor) Sensor 2
The signal voltage is too low.
P1234 B37 (Pedal value sensor) Sensor 2
The supply voltage is too high or too
low.
P1235 Recirculated air flap signal
output stage
P1236 Compressor output stage magnetic
coupling
P1237 read traction control system fault
memory
P1300 left crankshaft position sensor
(L5/4)
P1330 start control
P1330 Starter control Attempt at
starting without circuit 50
P1330 Starter control Open circuit
P1330 Starter control Short circuit
P1330 Starter control
P1335 Crankshaft position sensor L5/6
P1335 L5 (Crankshaft position sensor)
Overspeed detection
P1335 L5 (Crankshaft position sensor)
Plausibility 1
P1335 L5 (Crankshaft position sensor)
Plausibility 2
P1350 Injection advance solenoid valve
P1351 Start of delivery /injection
control loop
P1352 Needle lift motion sensor B27
P1353 Working speed control
P1354 deflexion angle between camshaft
and crankshaft
P1354 Synchronization between crankshaft
and camshaft Frequency of camshaft
signal is too high.
P1354 Synchronization between crankshaft
and camshaft Main injection correction
is faulty.
P1354 Synchronization between crankshaft
and camshaft No camshaft signal.
P1354 Synchronization between crankshaft
and camshaft No crankshaft signal.
P1354 Synchronization between crankshaft
and camshaft Plausibility
P1354 Synchronization between crankshaft
and camshaft The flow limiter has been
activated.
P1355 component Y80 (valve OFF,right
cylinder) can not be off while cylinder
is cut-off (OFF)
P1356 component Y81 (valve OFF,left
cylinder) can not be off while cylinder
is cut-off (OFF)
P1357 cylinder cut-off (function link):cylinder
intake valve still works when cylinder
is cut-off (ON)
P1358 cylinder 5 exhaust valve can not
work when cylinder is cut-off (OFF)(function
link)
P1359 cylinder 2 exhaust valve can not
work when cylinder is cut-off (OFF)(function
link)
P1360 cylinder 3 exhaust valve can not
work when cylinder is cut-off (OFF)(function
link)
P1361 cylinder 8 exhaust valve can not
work when cylinder is cut-off (OFF)(function
link)
P1366 Y93 (switch-over valve exhaust
valve)
P1380 cylinder intake valve can not work
when cylinder is cut-off (OFF)
P1384 FL knock sensor
P1385 RL knock sensor
P1386 Knock sensor system control module
control stop (A61)
P1386 right remove knock regulation
controller (N3/12)
P1397 left camshaft Hall sensor (B6/2)
P1400 Exhaust gas recirculation output
stage (Y12)
P1401 EGR lift sensor B28/3
P1401 EGR lift sensor B28/3
P1402 Exhaust gas recirculation
open-loop control
P1403 Exhaust gas recirculation Flow
check
P1403 exhaust gas recirculation
HFM-regulation
P1403 Exhaust gas recirculation
HFM-SFI-controlled
P1403 Exhaust gas recirculation Open
circuit
P1403 Exhaust gas recirculation Positive
control variation [Exhaust gas
recirculation rate is too high.]
P1403 Exhaust gas recirculation Positive
control variation [Exhaust gas
recirculation rate is too low.]
P1403 Exhaust gas recirculation Short
circuit
P1404 Exhaust gas recirculation AHR
closed-loop control
P1411 EGR lift sensor
P1420 air pump switch-over valve (Y32)
P1420 Air pump switchover valve (Y32)
P1437 No fault text specified at
present.
P1437 right CAT temperature sensor
(B16/5)
P1443 left work link EGR
P1444 left CAT temperature sensor
(B16/4)
P1444 No fault text specified at
present.
P1453 air pump relay (K17)
P1453 Air pump relay (K17),relay module
K76,fuse and relay module K40/4
P1460 Switchover valve 1 Y22 /7
P1461 Switchover valve 2 Y22 /6
P1463 left air inbreathe device inactive
P1465 Boost pressure control vacuum
transducer
P1470 Charge pressure control On/off
ration of actuation is too large.
P1470 Charge pressure control Open
circuit
P1470 Charge pressure control Positive
control variation [Charge pressure is
too high.]
P1470 Charge pressure control Positive
control variation [Charge pressure is
too low.]
P1470 Charge pressure control Short
circuit
P1470 intake air pressure regulation
P1470 Intake pressure or boost pressure
control
P1475 Resonance intake manifold
switchover valve Y22/6
P1475 Resonance intake manifold
switchover valve Y22/6
P1476 Resonance flap intake pipe Y22/7
P1480 Preglow indicator
P1480 pre-heating control
P1481 Glow plug failure Cylinder 1
P1481 Glow plug failure Cylinder 2
P1481 Glow plug failure Cylinder 3
P1481 Glow plug failure Cylinder 4
P1481 Glow plug failure Cylinder 5
P1481 Glow plug failure Cylinder 6
P1481 Glow plug failure Cylinder 7
P1481 Glow plug failure Cylinder 8
P1481 Glow plug failure
P1481 Glow Plugs
P1481 pre-heating plug fault
P1482 Glow output stage N14/2
P1482 N14/2 (Glow output stage) Cable
fault (Short circuit to ground)
P1482 N14/2 (Glow output stage)
Communication fault
P1482 N14/2 (Glow output stage) Excess
current
P1482 N14/2 (Glow output stage) FAULTY
P1482 N14/2 (Glow output stage)
Implausible reception byte
P1482 N14/2 (Glow output stage)
Incorrect diagnosis sequence
P1482 pre-heating plug output stage
N14/2
P1490 left EGR device switch-over valve
(Y58/2)
P1491 Refrigerant pressure in A/C system
too high
P1492 Exhaust flap (not relevant if not
fitted)
P1493 Exhaust flap output stage (not
relevant if not fitted)
P1510-001 speed meter touch switch
(S40/4)
P1510-003 MSM1 controller N3/5
P1515 maximal speed limit negative
difference
P1515 maximal vehicle speed limit
P1515 Maximum speed limiter
P1519 Camshaft timing function chain
P1519 right work link camshaft control
device
P1520 Cruise control switch S40
P1520 S40/4 (CC switch with variable
speed limiter) Control contact alone
P1520 S40/4 (CC switch with variable
speed limiter) DTR operating unit has
contact short (two contacts
simultaneously).
P1520 S40/4 (CC switch with variable
speed limiter) Negative acceleration
threshold
P1520 S40/4 (CC switch with variable
speed limiter) No check contact.
P1520 S40/4 (CC switch with variable
speed limiter) Operating parts signals
through CAN are implausible.
P1520 S40/4 (CC switch with variable
speed limiter) Positive acceleration
threshold
P1520 speed controller button type
switch
P1522 left work link camshaft control
device
P1525 Camshaft timing actuator (Y89)
P1525 right camshaft control device
regulation solenoid valve (Y49/2)
P1533 right camshaft control device
regulation solenoid valve (Y49/1)
P1542 Pedal value sensor (B71)
P1550 air compressor torque error
P1551 AC compressor shut-off output
stage
P1570 Fault in DAS to engine control
module (A61)
P1570 perform start test while closedown
FBS
P1570 right FBS and engine controller
interfered (N3/12)
P1580 Actuator (M33)
P1580 right regulation part (M16/3)
P1581 left regulation part (M16/4)
P1584 brake light switch (S9/1)
P1587 left controller voltage (N3/11)
P1588 left FBS to ME CAN BUS interfered
(N3/11)
P1589 right removing knock regulation
controller (N3/11)
P1590 fuel safety cut-off device
identified
P1592 ACS memory read error
P1603 CAN of EIS
P1604 CAN link to AAC
P1605 ABS RPM sensor bad channel
identification CAN BUS acceleration
signal
P1605 CAN acceleration info for poor
road recognition from ABS speed sensor
P1610 Actuation of holding relay Relay
Supply voltages switches off too late.
P1610 Actuation of holding relay Relay
Supply voltages switches off too soon.
P1610 No voltage supply or overvoltage
protection relay or relay module K1
P1610 security and relay module K40/4
P1611 Control module
P1611 controller N3/9
P1611 N3/9 (CDI control module) Sensor
supply voltage 1 Readout too large
P1611 N3/9 (CDI control module) Sensor
supply voltage 1 Readout too small
P1612 Control module Kl 15
P1612 signal Kl15
P1612 Voltage terminal 15 Analysis
circuit is faulty.
P1612 Voltage terminal 15
P1613 Control module
P1613 controller N3/9
P1613 N3/9 (CDI control module)
Stabilization Lower stabilization limit
P1613 N3/9 (CDI control module)
Stabilization Upper stabilization limit
P1614 Control module or fuel metering
control or fuel rack sensor or slide
valve sensor
P1614 controller N3/9
P1614 N3/9 (CDI control module)
Microcontroller COMMUNICATION 1
P1614 N3/9 (CDI control module)
Microcontroller COMMUNICATION 2
P1614 N3/9 (CDI control module)
Microcontroller Quantity stop
P1614 N3/9 (CDI control module)
Microcontroller Recovery error
P1614 N3/9 (CDI control module)
Microcontroller Shut-off monitoring
P1615 Control module supply voltage
P1615 controller supply voltage
P1615 N3/9 (CDI control module) Supply
voltage Signal is too large.
P1615 N3/9 (CDI control module) Supply
voltage Signal is too small.
P1616 Control module
P1617 Control module or not coded
P1617 controller N3/9 or not coded
P1617 EEPROM or incorrectly coded
Adaptation values of EEPROM
P1617 EEPROM or incorrectly coded AT has
been coded as MT.
P1617 EEPROM or incorrectly coded CAN
was interrupted during coding.
P1617 EEPROM or incorrectly coded
Codeword is incorrect or missing.
P1617 EEPROM or incorrectly coded EEPROM
COMMUNICATION
P1617 EEPROM or incorrectly coded MT has
been coded as AT.
P1617 EEPROM or incorrectly coded No
harmonizing version number
P1618 Control module
P1619 Control module or not coded
P1622 Injection pump shut-off valve
P1622 turnoff valve Y75
P1622 Y75 (Electric switchover valve)
Open circuit
P1622 Y75 (Electric switchover valve)
Plausibility
P1622 Y75 (Electric switchover valve)
Short circuit
P1622 Y75 Electric switchover valve open
circuit
P1625 EDC diesel malfunction indicator
lamp
P1626 Engine mount
P1630 drive authority signal
P1630 Drive authorization Control unit
Drive authorization does not answer
P1630 Drive authorization Incorrect
authentication value
P1630 Drive authorization Key used is
inhibited.
P1630 Drive authorization N3/9 (CDI
control module) EEPROM
P1630 Drive authorization signal
P1631 Slip detection signal
P1632 left controller (N3/11)
P1636 electric inspiration motor/air
condition M4/3
P1636 Electric suction fan Open circuit
P1636 Electric suction fan Short circuit
P1642 Engine control module Incorrect
coding MT coded has AT
P1643 Engine control module Incorrect
coding AT coded has MT,fault in CAN of
ETC
P1644 Transmission control module
Undervoltage Transmission version cannot
be checked
P1644 transmission variable cannot be
inspected (low voltage)
P1650-001 starter short circuit to
positive
P1650-002 starter discontinuity,short
circuit to ground
P1661 fuel injector 1 and 4 fuel
injector pressure
P1661 Injector voltage 1 Calculated
voltage below threshold
P1661 Injector voltage 1 Overvoltage
P1661 Injector voltage 1 Readout too
large
P1661 Injector voltage 1 Readout too
small
P1661 Injector voltage 1 Undervoltage
P1662 fuel injector 2 and 3 fuel
injector pressure
P1662 Injector voltage 2 Calculated
voltage below threshold
P1662 Injector voltage 2 Overvoltage
P1662 Injector voltage 2 Readout too
large
P1662 Injector voltage 2 Readout too
small
P1662 Injector voltage 2 Undervoltage
P1663 fuel pressure regulator Y74
P1663 Y74 (Pressure control valve) The
signal voltage is too high.
P1663 Y74 (Pressure control valve) The
signal voltage is too low.
P1664 Electric heater booster equipment
fault
P1664 electric heater fault
P1664 electric heater open
P1664 electric heater output stage fault
P1664 electric heater short
P1664 heater
P1664 load signal of electric heater
motor implausible
P1666 cutoff control
P1666 right or left cylinder (Y80,Y81) 'cylinder
cut-off' valve can not be turned on when
cylinder is cut-off.
P1666 Shut-off control Fault in
switching off throutgh injectors
P1666 Shut-off control Fault in
switching off throutgh zero quantity
P1673-001 engine/A/C electronic suction
device (M4/3) short circuit to positive
P1673-002 engine/A/C electronic suction
device (M4/3) short circuit to ground
P1681 air bag signal
P1681 Airbag signal Airbag signal
results in engine being switched off.
P1681 Airbag signal Short circuit to
positive
P1681 Crash-Signal unplausibel
P1681-001 crash signal identification
P1681-002 crash signal short circuit to
positive
P1681-003 crash signal error
P1698 A/C compressor cutoff
P1698 AC compressor shutoff CAN data
transfer
P1698 AC compressor shutoff Open circuit
P1698 AC compressor shutoff Short
circuit
P1699 Engine start/stop Engine start is
unsuccessful.
P1699 Engine start/stop Engine stop is
unsuccessful.
P1699 Engine start/stop Plausibility 1
P1699 Engine start/stop Plausibility 2
P1699 Engine start/stop Plausibility 3
P1699 Engine start/stop Plausibility
clutch DOWN
P1699 Engine start/stop Plausibility
clutch UP
P1705 Clutch signal or P/N position
Plausibility
P1705 Clutch signal or P/N position
P1705 Clutch switch or starter lockout
and reversing lamp switch
P1705 clutch switch
P1706 Transmisson neutral switch
P1747 control equipment EGS CAN-signal
error.
P1747 control equipment KIW CAN-signal
error.
P1747 EGS CAN BUS interfered
P1750 undervoltage
P1780 Modulating pressure switchover
valve Y3/4 or upshift delay Y3/5
P1780 Modulating pressure switchover
valve Y3/4
P1781 Upshift delay switchover valve
Y3/5
P1813 clutch switch (S40/3)
discontinuity,short circuit to ground
P1817-001 reversing light switch
S16/10s1 contact point short circuit to
ground
P1817-002 reversing light switch
S16/10s1 contact point short circuit to
positive
P1817-003 reversing light switch
S16/10s1 contact point discontinuity
P1817-004 reversing light switch
S16/10s1 A61 fault
P1817-005 reversing light switch
S16/10s1 power voltage
P1819-001 R/P lock contact switch short
circuit to ground
P1819-002 R/P lock contact switch short
circuit to positive
P1819-003 R/P lock contact switch
discontinuity
P1819-004 R/P lock contact switch,A61
fault
P1819-005 R/P lock contact switch supply
voltage
P1822 kickdown switch (S16/6) error
P1840 1-4 shift solenoid valve Y3/7y1
P1841 Solenoid valve Y3/7y2 3 shift
P1842 Solenoid valve Y3/7y3 2-5-R shift
P1843 Torque converter lockup clutch (KUeB)
Y3/7y4
P1844 Control solenoid valve Y3/7y5
shift pressure
P1849 Speed sensors supply voltage < 4 V
P1850 Transmission rpm sensor Y3/7n1
P1856-000 process recognition module
P1856-001 touch-function module
P1857 Gear oil temperature sensor Y3/7b1
P1858 Starter lockout contact Y3/7s1
short circuit
P1859 Supply voltage < 8.5 V or > 17 V
P1860 RR wheel speed of traction system
implausible,CAN
P1861 RL wheel speed of traction system
implausible,CAN
P1862 FR wheel speed of traction system
implausible,CAN
P1863 FL wheel speed of traction system
implausible,CAN
P1864 Accel.pedal value of motor
electronics implausible,CAN
P1865 Set engine torque of motor
electronics implausible,CAN
P1866 Engine speed of motor electronics
implausible,CAN
P1867 Engine torque of motor electronics
implausible,CAN
P1868 Altitude factor of motor
electronics implausible,CAN
P1869 Max.induced engine torque of motor
electronics implausible,CAN
P1871 Throttle valve value of motor
electronics implausible,CAN
P1872 Fault in CAN communication with
selector lever module or selector lever
implausible
P1873 Fault in CAN communication with
traction system
P1874 Engine oil temperature of motor
electronics implausible,CAN
P1875-000 common CAN communication
interfered
P1875-001 CAN communication with
instrument cluster interfered
P1875-001...255 same meaning
P1875-255 CAN communication with
instrument cluster interfered
P1876 Fault in CAN communication with
traction system
P1877 Fault in CAN communication with
engine electronics
P1878 Fault in CAN communication with
air conditioning
P1883 Transmission complete
P1886 1-4/-3 downshift PWM valve,pressure
too low or 2-5-R pressure too high
P1887 1-4 or 2-5 shift slide valve
jamming in pressure position,shift valve
pressure too high
P1888 1-4 or 2-5 shift slide valve
jamming in basic position,shift valve
pressure too low
P1889 2-5-R downshift PWM valve pressure
too low transmission slipping
P1890 Torque converter lockup clutch,impermissible
closing
P1891 Torque converter lockup clutch,high
power input
P1892 Transmission protection feedback
not received
P1893 1-4/-3 downshift PWM valve,pressure
too high
P1894 Control module not/incorrectly
coded
P1895 Control module N15/7 faulty
P1896 Control module N15/7 faulty
P1897 Control module N15/7 faulty
P1898 Control module N15/7 faulty
P1899 Control module N15/7 faulty
P1900 Control module N15/7 faulty
P1901 Control module N15/7 faulty
P1902 Control module N15/7 faulty
P1903 Control module N15/7 faulty
P1999 No fault text specified at
present.
P2000 Component N15/3 (ETC control
module) is faulty.
P2000 Component N15/3(ETC control
module) is faulty.
P2000 N3/9 (controller CDI) [checksum:error]
P2000 N3/9 (controller CDI) component
N3/9 (controller CDI) error variable
code
P2000 N3/9 (controller CDI) engine
synthesis characteristic curve error:error
code
P2000 N3/9 (controller CDI) hardware
identification error.
P2000 N3/9 (controller CDI) internal
error
P2000 N3/9 (controller CDI) software 'integration
check' error.
P2000 N3/9 (controller CDI) thruster
controller test
P2000 N3/9 (controller CDI) variable
code error.
P2001 check N3/9 (controller CDI) A/D
converter.
P2001 check N3/9 (controller CDI)
reference voltage
P2001 check N3/9 (controller CDI)
voltage supply 1.
P2001 check N3/9 (controller CDI)
voltage supply 2.
P2001 check N3/9 (controller CDI).Circuit
voltage supply unit fault
P2001 Component N15/3 (ETC control
module) is faulty.
P2001 Malfunction of exhaust gas
recirculation (functional chain)(P0400)
P2001 N3/9 (controller CDI) reset
identification error
P2001-001 M16/6 (throttle valve
regulation part),throttle valve position
reliability [P0638]
P2001-002 M16/6 (throttle valve
regulation part),PWM-signal:limit
2[P0638]
P2001-004 M16/6 (throttle valve
regulation part),PWM-signal interrupt
[P0638]
P2001-008 M16/6 (throttle valve
regulation part),PWM-signal:limit 1
P2002 Component N15/3(ETC control
module) is faulty.
P2002 cylinder 1 lasting injection
P2002 cylinder 2 lasting injection
P2002 cylinder 3 lasting injection
P2002 cylinder 4 lasting injection
P2002 cylinder 5 lasting injection
P2002 cylinder 6 lasting injection
P2002 cylinder 7 lasting injection
P2002 cylinder 8 lasting injection
P2002-001 B37 (pedal position sensor)
Hall sensor 1,positive short [P0123]
P2002-002 B37 (pedal position sensor)
Hall sensor 1,short caused by open wire
[P0122]
P2002-004 B37 (pedal position sensor)
Hall sensor 2,positive short [P0223]
P2002-008 B37 (pedal position sensor)
Hall sensor 2,short caused by open wire
[P0222]
P2002-016 B37 (pedal position sensor)
Hall sensor 1 voltage and Hall sensor 2
voltage not match [P0121]
P2003 check position regulator.Left air
mass boost balance position on the high
side
P2003 check position regulator.Right air
mass boost balance position on the high
side
P2003 Component N15/3(ETC control
module) is faulty.
P2003 Malfunction of secondary air
injection (function chain)(P0410)
P2003 right cylinder bank intake error (work
link)(P0410)
P2003-001 controller sensor voltage
supply over range,voltage too high
P2003-002 controller sensor voltage over
range,voltage too high
P2004 B2/5 (HFM sensor)(P0100)
P2004 B2/5 (Hot film MAF sensor)(P0100)
P2004 check external voltage
supply.Battery voltage too high
P2004 check external voltage
supply.Battery voltage too low
P2004 check external voltage
supply.Control of holding relay K40/7km
(relay CDI) cutoff too early.
P2004 check external voltage
supply.KI.15:hardware (HW) turn-on;CAN-BUS
turnoff
P2004 check external voltage
supply.Relay (diesel engine voltage
supply relay) cutoff too late.
P2004 Component N15/3(ETC control
module) is faulty.
P2004-001 B18 (high pressure sensor)
signal,positive/wire open cause short
[P0108]
P2004-002 B18 (high pressure sensor)
signal,overload short [P0107]
P2004-004 B18 (high pressure sensor)
signal,engine off B28 (pressure sensor)
signal and B18 (high pressure sensor)
signal different[P0106]
P2005 B11/4 (Coolant temperature
sensor)(P0115)
P2005 B11/4 (refrigerant temperature
sensor)(P0115)
P2005 check L5 (crankshaft position
sensor).Impulse number invalid
P2005 check L5 (crankshaft position
sensor).Negative rotate speed grads too
large
P2005 check L5 (crankshaft position
sensor).Over speed
P2005 check L5 (crankshaft position
sensor).Positive rotate speed grads too
large
P2005 check L5 (crankshaft position
sensor).Signal interrupted while
operating
P2005 check L5 (crankshaft position
sensor).Signal interrupted while
starting
P2005 check L5 (crankshaft position
sensor).Synchronization between
crankshaft and camshaft implausible
P2005 Component N15/3(ETC control
module) is faulty.
P2005-001 B11/4 (refrigerant temperature
sensor),positive/wire open cause short
[P0118]
P2005-002 B11/4 (refrigerant temperature
sensor),overload short [P0117]
P2005-004 B11/4 (refrigerant temperature
sensor),¦Ë adaptation required minimal
engine rpm not reach [P0125]
P2005-008 B11/4 (refrigerant temperature
sensor),signal error [P0116]
P2005-016 B11/4 (refrigerant temperature
sensor),signal error [P0119]
P2005-032 refrigerant temperature rise
too slow.[P0128]
P2006 B2/5b1 (intake temperature sensor)
(P0110)
P2006 check B6/1 (camshaft Hall sensor).
Signal too strong. Short to positive
P2006 check B6/1 (camshaft Hall sensor).
Signal too weak. Short to ground
P2006 Component N15/3(ETC control
module) is faulty.
P2006 fuel pre-supply pressure sensor
implausible
P2006 fuel pre-supply pressure sensor
signal value too large
P2006 fuel pre-supply pressure sensor
signal value too small
P2006-001 B2/5b1 (outside air
temperature sensor) signal, positive/wire
open cause short [p0113]
P2006-002 B2/5b1 (outside air
temperature sensor) signal, overload
short [P0112]
P2007 B28 (Pressure sensor)(P0105)
P2007 check B11/4 (coolant temperature
sensor).Dynamic check implausible.
P2007 check B11/4 (coolant temperature
sensor).Signal voltage too high.
P2007 check B11/4 (coolant temperature
sensor).Signal voltage too low.
P2007 Component N15/3(ETC control
module) is faulty.
P2007 control fuel pre-supply pressure,
reliability
P2007 inspect difference between fuel
pre-supply pressure and rating pressure
P2007 inspect fuel pre-supply pressure,
fuel filter break
P2007 inspect fuel pre-supply pressure,
fuel pre-supply pressure too low
P2007-001 A16 (knock sensor) [P0325]
P2008 check B40 (engine oil sensor
(level,temperature and quality)). Engine
oil sensor intermittent error
P2008 check B40 (engine oil sensor
(level,temperature and quality)). Level
implausible.
P2008 check B40 (engine oil sensor
(level,temperature and quality)). Not
break down synchronously.
P2008 check B40 (engine oil sensor
(level,temperature and quality)). Oil
quality implausible.
P2008 check B40 (engine oil sensor
(level,temperature and quality)). Oil
temperature implausible.
P2008 check B40 (engine oil sensor
(level,temperature and quality)). Short/no
signal.
P2008 component G3/9 (right O2 sensor,before
CAT,CYL 1-3) heating (P0135)
P2008 Component N15/3(ETC control
module) is faulty.
P2008 Heating of component G3/4 (Right
O2 sensor,before TWC[CAT])(P0135)
P2008 Rail pressure variation:The rail
pressure is too high.
P2008 Rail pressure variation:The rail
pressure is too low.
P2008-001 M16/6 (throttle valve
regulation part) practical potentiometer
1,signal voltage too high.
P2008-002 M16/6 (throttle valve
regulation part) practical potentiometer
1,signal voltage too low.
P2008-004 M16/6 (throttle valve
regulation part) practical potentiometer
1 and practical potentiometer 2
comparison error
P2008-008 M16/6 (throttle valve
regulation part) practical potentiometer
1 and HFM voltage signal comparison
error
P2009 check B4/6 (fuel rail pressure
sensor).Signal voltage too high.
P2009 check B4/6 (fuel rail pressure
sensor).Signal voltage too low.
P2009 component G3/13 (right O2 sensor,after
CAT,CYL 1-3)(P0141)
P2009 Component N15/3(ETC control
module) is faulty.
P2009 fuel water content sensor.(fuel
filter)
P2009 Heating of component G3/6 (Right
O2 sensor,after TWC[CAT])(P0141)
P2009-001 M16/6 (throttle valve
regulation part) practical potentiometer
2,signal voltage too high.
P2009-002 M16/6 (throttle valve
regulation part) practical potentiometer
2,signal voltage too low.
P2009-004 M16/6 (throttle valve
regulation part) practical potentiometer
2,practical potentiometer 1 comparison
error
P2009-008 M16/6 (throttle valve
regulation part) practical potentiometer
2 and HFM voltage signal comparison
error
P200A Component N15/3(ETC control
module) is faulty.
P200A Knock sensor system of control
module N3/10 (ME-SFI control
module),Hardware fault
P200A-001 M16/6 (throttle valve
regulation part) practical
potentiometer,not initialization
P200A-002 M16/6 (throttle valve
regulation part) practical
potentiometer,position urgency start
P200A-004 M16/6 (throttle valve
regulation part) practical
potentiometer,adaptation urgency start
P200A-008 M16/6 (throttle valve
regulation part) practical
potentiometer,N3/10 (ME controller)
P200B Component N15/3(ETC control
module) is faulty.
P200B cylinder 1-3 CAT too weak.(P0422)
P200B The efficiency of the right
catalytic converter is insufficient.(P0422)
P200B-001 B2/5 (HF type AFM sensor),positive
short [P0103]
P200B-002 B2/5 (HF type AFM sensor),overload/wire
open cause short [P0102]
P200B-004 B2/5 (HF type AFM sensor),air
mass sensor/throttle valve reliability
error [P0101]
P200C Component N15/3(ETC control
module) is faulty.
P200C G3/4 (Right O2 sensor,before TWC[CAT])
Aging,correction variable exceeded
P200C G3/9 (right O2 sensor,before CAT,CYL
1-3) aging,calibration program jump over
P200C-001 B6/1 (camshaft Hall sensor),no
signal [P0340]
P200C-002 B6/1 (camshaft Hall sensor),signal
error [P0341]
P200D Component N15/3 (ETC control
module) is faulty.
P200D Component N15/3(ETC control
module) is faulty.
P200D G3/4 (Right O2 sensor,before TWC[CAT])
Aging,period too long (P0133)
P200D G3/9 (right O2 sensor,before CAT,CYL
1-3) aging,used too long (P0133)
P200D-001 L5 (crankshaft position
sensor),no signal [P0335]
P200D-002 L5 (crankshaft position
sensor),signal error [P0336]
P200D-004 L5 (crankshaft position
sensor),signal line/wire interrupt cause
short [P0335]
P200E G3/13 (right O2 sensor,after CAT,CYL
1-3) no special status variation
P200E G3/6 (Right O2 sensor,after TWC[CAT])
P200E-001 component N15/3 (EGS
controller) trouble stored.[P0702]
P200E-002 component N15/3 (EGS
controller) trouble stored.[P0753]
P200E-004 component N15/3 (EGS
controller) trouble stored.[P0758]
P200E-008 component N15/3 (EGS
controller) trouble stored.[P0763]
P200E-016 component N15/3 (EGS
controller) trouble stored.[P0743]
P200E-032 component N15/3 (EGS
controller) trouble stored.[P0748]
P200E-064 component N15/3 (EGS
controller) trouble stored.[P0748]
P200E-128 component N15/3 (EGS
controller) trouble stored.[P0702]
P200F G3/4 (Right O2 sensor,before TWC[CAT])(P0130)
P200F G3/9 (right O2 sensor,before CAT,CYL
1-3),too small voltage up (P0130)
P200F-001 component N15/3 (EGS
controller) trouble stored.[P0715]
P200F-002 component N15/3 (EGS
controller) trouble stored.[P0705]
P200F-004 component N15/3 (EGS
controller) trouble stored.[P0720]
P200F-008 component N15/3 (EGS
controller) trouble stored.[P0700]
P200F-016 component N15/3 (EGS
controller) trouble stored.[P0700]
P200F-032 component N15/3 (EGS
controller) trouble stored.[P0740]
P200F-064 component N15/3 (EGS
controller) trouble stored.[P0730]
P2010 Control module N15/3(ETC control
module is not coded.
P2010 G3/13 (right O2 sensor,after CAT,CYL
1-3),electrical malfunction (P0136)
P2010 G3/6 (Right O2 sensor,after TWC[CAT])(P0136)
P2010-001 Y62/y1 (cylinder 1 fuel
injector),positive short [P0262]
P2010-002 Y62/y1 (cylinder 1 fuel
injector),overload short [P0261]
P2010-003 Y62/y1 (cylinder 1 fuel
injector),wire interrupt [P0201]
P2011 A16/1 (Knock sensor 1,right)
P2011 check B2/6 (left hot film air flow
meter).Implausible
P2011 check B2/6 (left hot film air flow
meter).Signal voltage too high.
P2011 check B2/6 (left hot film air flow
meter).Signal voltage too low.
P2011 check B2/6 (right hot film air
flow meter).Signal voltage too high.
P2011 check B2/6 (right hot film air
flow meter).Signal voltage too low.
P2011 check B2/7 (right hot film air
flow meter).Implausible
P2011 check hot film air flow
meter.Creditability error
P2011 The coding of the control unit
N15/3 (ETC control module) is
impermissible.
P2011 The coding of the control unit
N15/3(ETC control module) is
impermissible.
P2011-001 Y62/y3 (cylinder 3 fuel
injector),positive short [P0268]
P2011-002 Y62/y3 (cylinder 3 fuel
injector),overload short [P0267]
P2011-003 Y62/y3 (cylinder 3 fuel
injector),wire interrupt [P0203]
P2012 check B17 (intake air temperature
sensor).Signal voltage too high.
P2012 check B17 (intake air temperature
sensor).Signal voltage too low.
P2012 The checksum of the standard
software status for component N15/3 (ETC
control module) is missing or is not
entered.
P2012 Y58/4 (Activated charcoal canister
shut-off valve)(P0446)
P2012 Y58/4 (canister lock valve)(work
link)(P0446)
P2012-001 Y62/y4 (cylinder 4 fuel
injector),positive short [P0271]
P2012-002 Y62/y4 (cylinder 4 fuel
injector),overload short [P0270]
P2012-003 Y62/y4 (cylinder 4 fuel
injector),wire interrupt [P0204]
P2013 check B28 (pressure sensor).Intake
air pressure/atmosphere pressure
implausible
P2013 check B28 (pressure sensor).Signal
voltage too high.
P2013 check B28 (pressure sensor).Signal
voltage too low.
P2013 check B28/5 (pressure sensor
behind the air cleaner).Atmosphere
pressure value implausible.
P2013 check B28/5 (pressure sensor
behind the air cleaner).Intake air
manifold pressure signal too large.
P2013 check B28/5 (pressure sensor
behind the air cleaner).Intake air
manifold pressure signal too small.
P2013 Component N15/3(ETC control
module) is faulty.
P2013 EGR system severe leaks (P0455)
P2013 Major leak in purge system (P0455)
P2013 N3/9 (controller CDI)/atmosphere
pressure sensor.Signal voltage too high.
P2013 N3/9 (controller CDI)/atmosphere
pressure sensor.Signal voltage too low.
P2013-001 Y62/y2 (cylinder 2 fuel
injector),positive short [P0265]
P2013-002 Y62/y2 (cylinder 2 fuel
injector),overload short [P0264]
P2013-003 Y62/y2 (cylinder 2 fuel
injector),wire interrupt [P0202]
P2014 check B19/3 (left catalyzer
temperature sensor after supercharger).Signal
voltage too high.
P2014 check B19/3 (left catalyzer
temperature sensor after supercharger).Signal
voltage too low.
P2014 check B19/4 (right catalyzer
temperature sensor,after supercharger).Signal
voltage too high.
P2014 check B19/4 (right catalyzer
temperature sensor,after supercharger).Signal
voltage too low.
P2014 check B19/5 (left catalyzer
temperature sensor before supercharger).Signal
voltage too low.
P2014 check B19/5 (left catalyzer
temperature sensor,before bottom
catalyzer).Signal voltage too high.
P2014 check B19/6 (right catalyzer
temperature sensor,before bottom
catalyzer).Signal voltage too high.
P2014 check B19/6 (right catalyzer
temperature sensor,before bottom
catalyzer).Signal voltage too low.
P2014 EGR system slight leaks (P0442)
P2014 Purge control system has slight
leak (P0442)
P2014-001 Y49 (camshaft control device
regulation solenoid valve),positive
short [P0010]
P2014-002 Y49 (camshaft control device
regulation solenoid valve),overload
short [P0010]
P2014-004 Y49 (camshaft control device
regulation solenoid valve),wire
interrupt [P0010]
P2014-008 Y49 (camshaft control device
regulation solenoid valve),mechanical
malfunction [P0010]
P2015 check start control.Circuit open
P2015 check start control.short to
ground
P2015 check start control.Short
P2015 EGR system leaks (work
link)(P0440)
P2015 Purge control system has leak (function
chain)(P0440)
P2015-001 S40/3 (clutch pedal switch),trouble
P2016 check Y76y1 (cylinder 1 fuel
injector).Short
P2016 check Y76y2 (cylinder 2 fuel
injector).Short
P2016 check Y76y3 (cylinder 3 fuel
injector).Short
P2016 check Y76y4 (cylinder 4 fuel
injector).Short
P2016 check Y76y5 (cylinder 5 fuel
injector).Short
P2016 check Y76y6 (cylinder 6 fuel
injector).Short
P2016 check Y76y7 (cylinder 7 fuel
injector).Short
P2016 check Y76y8 (cylinder 8 fuel
injector).Short
P2016 cylinder 1-3 mixture self
regulation reach limit (part load)(P0170)
P2016 Self-adaptation of mixture
formation for right bank of cylinders is
at limit value (at part load).(P0170)
P2016-001 Y58/1 (EGR device switch-over
valve),positive short [P0445]
P2016-002 Y58/1 (EGR device switch-over
valve),overload short [P0445]
P2016-004 Y58/1 (EGR device switch-over
valve),wire interrupt [P0444]
P2016-008 Y58/1 (EGR device switch-over
valve),valve stick condition
pen
[P0443]
P2017 check Y76y1 (cylinder 1 fuel
injector).Fault
P2017 check Y76y2 (cylinder 2 fuel
injector).Fault
P2017 check Y76y3 (cylinder 3 fuel
injector).Fault
P2017 check Y76y4 (cylinder 4 fuel
injector).Fault
P2017 check Y76y5 (cylinder 5 fuel
injector).Fault
P2017 check Y76y6 (cylinder 6 fuel
injector).Fault
P2017 check Y76y7 (cylinder 7 fuel
injector).Fault
P2017 check Y76y8 (cylinder 8 fuel
injector).Fault
P2017 cylinder 1-3 mixture self
regulation reach limit (idle)(P0170)
P2017 Self-adaptation of mixture
formation for right bank of cylinders is
at limit value (at idle speed).(P0170)
P2017-001 K40k1 (fuel pump relay)/K27 (fuel
pump relay)/N10/2kA (fuel pump relay),positive
short
P2017-002 K40k1 (fuel pump relay)/K27 (fuel
pump relay)/N10/2kA (fuel pump relay),overload
short
P2017-004 K40k1 (fuel pump relay)/K27 (fuel
pump relay)/N10/2kA (fuel pump relay),wire
interrupt
P2018 check
M3
(fuel pump).Circuit open
P2018 check M3 (fuel pump).Short to
ground
P2018 check M3 (fuel pump).Short
P2018 cylinder 1-3 mixture self
regulation reach limit (between idle and
part load)
P2018 Self-adaptation of mixture
formation for right bank of cylinders is
at limit value (between idle speed and
part load).(P0170)
P2018-001 Y32 (air pump switch-over
valve),positive short [P0414]
P2018-002 Y32 (air pump switch-over
valve),overload short [P0414]
P2018-004 Y32 (air pump switch-over
valve),wire interrupt [P0413]
P2019 check Y74 (pressure regulation
valve).Current in pressure regulation
valve too small
P2019 check Y74 (pressure regulation
valve).Current pressure regulation valve
too large
P2019 check Y74 (pressure regulation
valve).Regulation error
P2019 check Y94 (flux regulation valve).Current
too large
P2019 check Y94 (flux regulation valve).Current
value too small
P2019 check Y94 (flux regulation valve).Regulation
error too large
P2019 Power output limited because of
excessively high temperature of coolant
P2019 power restricted by high
refrigerant temperature
P2019-001 K40/4k3 (air pump relay),N10/1KO
(air pump relay),positive short [P0410]
P2019-002 K40/4k3 (air pump relay),N10/1KO
(air pump relay),overload short [P0410]
P201A B6/1 (Camshaft Hall sensor)(P0341)
P201A B6/3 (camshaft Hall sensor,right
cylinder bank)(P0341)
P201A-001 wheel adaptive sensor,gear gap
error/mechanical malfunction [P0335]
P201A-002 wheel adaptive sensor,error
regulation [P0335]
P201B component N3/10 (ME controller)
supply voltage (P0560)
P201B Voltage supply of component N3/10
(ME-SFI control module)(P0560)
P201B-001 cylinder 1 interrupt device,CAT
malfunction [P0301]
P201B-002 cylinder 3 interrupt device,CAT
malfunction [P0303]
P201B-004 cylinder 4 interrupt device,CAT
malfunction [P0304]
P201B-008 cylinder 2 interrupt device,CAT
malfunction [P0302]
P201B-016 cylinder 1 interrupt device,CAT
malfunction fuel insufficient
P201B-032 cylinder 3 interrupt device,CAT
malfunction fuel insufficient
P201B-064 cylinder 4 interrupt device,CAT
malfunction fuel insufficient
P201B-128 cylinder 2 interrupt device,CAT
malfunction fuel insufficient
P201C B4/3 (fuel tank pressure sensor),electrical
malfunction (P0450)
P201C Misfiring at several cylinders
[P0300]
P201C-001 cylinder 1 interrupt device
[P0301]
P201C-002 cylinder 3 interrupt device
[P0303]
P201C-004 cylinder 4 interrupt device
[P0304]
P201C-008 cylinder 2 interrupt device
[P0302]
P201C-016 cylinder 1 interrupt device
fuel insufficient
P201C-032 cylinder 3 interrupt device
fuel insufficient
P201C-064 cylinder 4 interrupt device
fuel insufficient
P201C-128 cylinder 2 interrupt device
fuel insufficient
P201D Y62y1 (cylinder 1 injector)(P0201)
P201D Y62y1 (Fuel injector cylinder
1)(P0201)
P201D-001 mixture formation unit
adaptation,part load mixture too rich.[P0172]
P201D-002 mixture formation unit
adaptation,part load mixture too lean.[P0171]
P201D-004 mixture formation unit
adaptation,idle mixture too rich.[P0172]
P201D-008 mixture formation unit
adaptation,idle mixture too lean.[P0171]
P201E Y62y5 (cylinder 1 injector)(P0205)
P201E Y62y5 (Fuel injector cylinder
5)(P0205)
P201E-001 CAT effect too small [P0420]
P201F Y62y3 (cylinder 5 injector)(P0203)
P201F Y62y4 (Fuel injector cylinder
4)(P0204)
P201F-001 B40 (engine oil sensor (engine
oil condition,temperature and quality)),electrical
malfunction
P201F-002 B40 (engine oil sensor (engine
oil condition,temperature and quality)),engine
oil temperature
P201F-004 B40 (engine oil sensor (engine
oil condition,temperature and quality)),engine
oil quality
P201F-008 B40 (engine oil sensor (engine
oil condition,temperature and quality)),engine
oil condition
P201F-016 B40 (engine oil sensor (engine
oil condition,temperature and quality)),engine
oil quality error
P2020 check fuel rail pressure:B4/6 (fuel
rail pressure sensor) racing test.
P2020 check fuel rail pressure:Y74 (pressure
regulation valve) racing test.
P2020 check fuel rail pressure:Y94 (flux
regulation valve) racing test.
P2020 check Y74 (pressure regulation
valve).Short
P2020 check Y94 (flux regulation valve).Short
P2020 Y62y2 (Fuel injector cylinder
2)(P0202)
P2020 Y62y6 (cylinder 5 injector)(P0206)
P2020-001 M4/3 (engine/A/C electronic
intake air device),positive short
P2020-002 M4/3 (engine/A/C electronic
intake air device),overload/wire open
cause short
P2021 check Y74 (pressure
regulation valve).Current in pressure
regulation valve too large
P2021 check Y74 (pressure regulation
valve).Current in pressure regulation
valve too small.Fuel rail pressure too
high.
P2021 check Y74 (pressure regulation
valve).Current/fuel rail pressure too
large
P2021 check Y74 (pressure regulation
valve).Current/fuel rail pressure too
small
P2021 check Y74 (pressure regulation
valve).Fuel rail pressure too small.
P2021 check Y74 (pressure regulation
valve).Maximal pressure will be rewrite.
P2021 check Y74 (pressure regulation
valve).Negative regulation error
P2021 check Y74 (pressure regulation
valve).Regulation error too large
P2021 Y62y2 (cylinder 5 injector)(P0202)
P2021 Y62y6 (Fuel injector cylinder
6)(P0206)
P2021-001 starter relay,positive short
P2021-002 starter relay,overload/wire
open cause short
P2022 check fuel injector.Cylinder 1
misfire
P2022 check fuel injector.Cylinder 2
misfire
P2022 check fuel injector.Cylinder 3
misfire
P2022 check fuel injector.Cylinder 4
misfire
P2022 check fuel injector.Cylinder 5
misfire
P2022 check fuel injector.Cylinder 6
misfire
P2022 check fuel injector.Cylinder 7
misfire
P2022 check fuel injector.Cylinder 8
misfire
P2022 Y62y3 (Fuel injector cylinder
3)(P0203)
P2022 Y62y4 (cylinder 5 injector)(P0204)
P2022-001 component G3/2 (before CAT O2
sensor) heating device,positive short
[P0135]
P2022-002 component G3/2 (before CAT O2
sensor) heating device,overload short
[P0135]
P2022-004 component G3/2 (before CAT O2
sensor) heating device,wire interrupt
[P0135]
P2022-008 component G3/2 (O2 sensor
before CAT) heating device,heating power
too small.[P0135]
P2023 check Y83 (intake air manifold
turnoff switch valve).Circuit open
P2023 check Y83 (intake air manifold
turnoff switch valve).It is OFF when
left intake air manifold is closed.
P2023 check Y83 (intake air manifold
turnoff switch valve).It is OFF when
right intake air manifold is closed.
P2023 check Y83 (intake air manifold
turnoff switch valve).It is ON when left
intake air manifold is closed.
P2023 check Y83 (intake air manifold
turnoff switch valve).It is ON when
right intake air manifold is closed.
P2023 check Y83 (intake air manifold
turnoff switch valve).Short to ground
P2023 check Y83 (intake air manifold
turnoff switch valve).Short
P2023 K40/7kN (air pump relay)(P0410)
P2023 K40/7kN (Air pump relay)(P0410)
P2023-001 component G3/1 (O2 sensor
before CAT) heating device,positive
short [P0141]
P2023-002 component G3/1 (O2 sensor
before CAT) heating device,overload
short [P0141]
P2023-004 component G3/1 (O2 sensor
before CAT) heating device,wire
interrupt [P0141]
P2023-008 component G3/2 (O2 sensor
before CAT) heating device,heating power
too small.[P0141]
P2024 check Y27/10 (right exhaust gas
recirculation regulator) regulator fault
(via ground key).
P2024 check Y27/10 (right exhaust gas
recirculation regulator).Circuit open
P2024 check Y27/10 (right exhaust gas
recirculation regulator).Short to ground
P2024 check Y27/10 (right exhaust gas
recirculation regulator).Short
P2024 check Y27/9 (left exhaust gas
recirculation regulator) regulator fault
(via ground key).
P2024 check Y27/9 (left exhaust gas
recirculation regulator).Circuit open
P2024 check Y27/9 (left exhaust gas
recirculation regulator).Short to ground
P2024 check Y27/9 (left exhaust gas
recirculation regulator).Short
P2024 Y32 (Air pump switchover valve)(P0412)
P2024 Y32/2 (air pump switch-over valve,right
cylinder bank)(P0412)
P2024-001 B28 (pressure sensor),positive
short/wire open cause short [P0108]
P2024-002 B28 (pressure sensor),overload
short [P0107]
P2024-004 B28 (pressure sensor),engine
inactive B28 (pressure sensor) signal
not equal to B18 (high pressure sensor)
signal [P0106]
P2025 check M16/5 (throttle valve
regulator).Circuit open
P2025 check M16/5 (throttle valve
regulator).M16/5 (throttle valve
regulator) regulator fault (via ground
key).
P2025 check M16/5 (throttle valve
regulator).Short to ground
P2025 check M16/5 (throttle valve
regulator).Short
P2025 Y58/4 (Activated charcoal canister
shut-off valve)(P0446)
P2025 Y58/4 (canister closedown valve)(P0446)
P2025-001 T1/1 (cylinder 1 ignition coil)
ignition duration,value too small
[P0351]
P2025-002 T1/1 (cylinder 1 ignition coil)
primary voltage [P0351]
P2025-004 T1/3 (cylinder 3 ignition coil)
ignition duration,value too small
[P0353]
P2025-008 T1/3 (cylinder 3 ignition coil)
primary voltage [P0353]
P2025-016 T1/4 (cylinder 4 ignition coil)
ignition duration,value too small
[P0354]
P2025-032 T1/4 (cylinder 4 ignition coil)
primary voltage [P0354]
P2025-064 T1/2 (cylinder 2 ignition coil)
ignition duration,value too small
[P0352]
P2025-128 T1/2 (cylinder 2 ignition coil)
primary voltage [P0352]
P2026 exhaust gas recirculation negative
regulation deviation/exhaust gas
recirculation rate too high.
P2026 exhaust gas recirculation positive
regulation deviation/exhaust gas
recirculation rate too low.
P2026 Y58/1 (EGR switch-over valve)(P0443)
P2026 Y58/1 (Purge control valve)(P0443)
P2026-001 CAN BUS signal from N15/3 (EGS
controller) controller,CAN BUS signal
error [P0600]
P2026-002 CAN BUS signal from N15/3 (EGS
controller) controller,CAN BUS signal
error [P0600]
P2026-004 CAN BUS signal from N15/3 (EGS
controller) controller,CAN BUS signal
error (torque) [P0600]
P2026-008 CAN BUS signal from N15/3 (EGS
controller) controller,CAN BUS signal
error [P0600]
P2026-016 CAN BUS signal from N15/3 (EGS
controller) controller,CAN BUS signal
interrupt [P0600]
P2027 Y100 (left boost regulator)
circuit open
P2027 Y100 (left boost regulator)
regulator fault (via ground key).
P2027 Y100 (left boost regulator) short
to ground
P2027 Y100 (left boost regulator) short
P2027 Y100/1 (right boost regulator)
circuit open
P2027 Y100/1 (right boost regulator)
regulator fault (via ground key).
P2027 Y100/1 (right boost regulator)
short to ground
P2027 Y100/1 (right boost regulator)
short
P2027 Y31/1 (EGR vacuum transducer)(P0403)
P2027-001 CAN BUS signal from N47-5
(ESP,PML and BAS controller) controller,CAN
BUS signal error
P2027-002 CAN BUS signal from N47-5
(ESP,PML and BAS controller) controller,CAN
BUS signal error
P2027-004 CAN BUS signal from N47-5
(ESP,PML and BAS controller) controller,CAN
BUS signal error
P2027-008 CAN BUS signal from N47-5
(ESP,PML and BAS controller) controller,CAN
BUS signal error (torque)
P2027-016 CAN BUS signal from N47-5
(ESP,PML and BAS controller) controller,CAN
BUS signal interrupt [P0600]
P2027-032 CAN BUS signal from N47-5
(ESP,PML and BAS controller) controller,CAN
BUS signal from (brake light switch)
P2027-064 CAN BUS signal from N47-5
(ESP,PML and BAS controller) controller,CAN
BUS signal from (brake light switch)
P2028 boost regulator negative
regulation deviation/boost pressure too
high.
P2028 boost regulator positive
regulation deviation/boost pressure too
low.
P2028 the fill-in coefficient of this
component exeeded
P2028 Y49/2 (camshaft adjusting
valve,right cylinder bank)(P0340)
P2028-001 battery voltage too low
[P0562]
P2028-002 battery voltage too high/error
[P0563]
P2029 check S40/4 (button type switch
TPM with variable speed limit).Closed
P2029 check S40/4 (button type switch
TPM with variable speed limit).Negative
acceleration limit
P2029 check S40/4 (button type switch
TPM with variable speed limit).Positive
acceleration limit
P2029 right cylinder bank camshaft
adjustment (work link)(P0340)
P2029-001 engine RPM signal,error
P202A left cylinder bank camshaft
adjustment (work link)(P0340)
P202A-004 mixture formation unit
adaptation lean [P0172]
P202A-008 mixture formation unit
adaptation too rich [P0171]
P202B idle regulation error (P0507)
P202B Idle speed control implausible
(P0507)
P202B-001 CAN BUS signal from ESP
controller,speed signal error [P0500]
P202B-002 CAN BUS signal from ESP
controller,speed signal error
P202B-004 CAN BUS signal from ESP
controller,speed signal error
P202B-008 CAN BUS signal from ESP
controller,speed signal error
P202B-016 CAN BUS signal from ESP
controller,speed signal error
P202C Coolant thermostat (P0115)
P202C refrigerant temperature regulator
(P0115)
P202C-001 CAN BUS signal from EIS
controller,CAN BUS signal interrupt
P202C-002 signal from EIS controller CAN
BUS,CAN BUS signal error
P202C-004 CAN BUS signal from EIS
controller,CAN BUS signal error
P202C-008 CAN BUS signal from EIS
controller,CAN BUS signal interrupt
drive authority
P202D B11/4 (Coolant temperature
sensor),Plausibility (P0115)
P202D B11/4 (refrigerant temperature
sensor),reliability (P0115)
P202D-001 CAN BUS signal from
combination instrument controller,CAN
BUS signal interrupt
P202D-002 CAN BUS signal from
combination instrument controller,fuel
tank charging condition error
P202D-004 CAN BUS signal from
combination instrument
controller,outside temperature error
P202E M16/6 (throttle valve
actuator)(P0120)
P202E M16/6 (throttle valve
regulator)(P0120)
P202E-001 CAN BUS signal from KLA/TAU
controller,CAN BUS signal interrupt
P202F No or incorrect CAN message from
control unit N51/2 (ABC control
module)(P0600)
P202F no signal or error signal from
N51/2 (ABC controller) controller BUS
(P0600)
P202F-001 CAN BUS error,1 CAN BUS
controller:CAN off [P0600]
P202F-002 CAN BUS error,2 CAN BUS
controller:CAN off [P0600]
P2030 check heat time
control.Communication fault
P2030 check heat time control.N14/2
(pre-heating plug output stage) fault
P2030 check heat time
control.Pre-heating indicator fault
P2030 check heat time
control.Pre-heating plug short
P2030 No faulty code text
P2030 No faulty code text
P2030 No or incorrect CAN message from
control unit N15/5 (electronic selector
lever module control module)(P0600)
P2030 no signal or error signal from
N15/5 (electronic shift lever mode
controller) controller BUS (P0600)
P2030-001 crash signal,error
P2030-002 crash signal,front crash
P2030-004 Crash signal,positive short
P2031 cylinder 1 pre-heating plug
P2031 cylinder 2 pre-heating plug
P2031 cylinder 3 pre-heating plug
P2031 cylinder 4 pre-heating plug
P2031 cylinder 5 pre-heating plug
P2031 cylinder 6 pre-heating plug
P2031 cylinder 7 pre-heating plug
P2031 cylinder 8 pre-heating plug
P2031 No faulty code text
P2031 No or incorrect CAN message from
control unit N80 (Jacket tube
module)(P0600)
P2031 no signal or error signal from
N15/5 (electronic shift lever mode
controller) controller BUS (P0600)
P2031-002 G3/2 (before CAT O2 sensor)
aging,used too long [P0133]
P2031-004 G3/2 (before CAT O2 sensor),overload
short [P0131]
P2031-008 G3/2 (before CAT O2 sensor),positive
short [P0132]
P2031-016 G3/2 (before CAT O2 sensor),interrupt
[P0130]
P2031-032 G3/2 (before CAT O2 sensor) at
off sensor signal error [P0130]
P2032 M16/6r1 (Throttle valve actual
value potentiometer)(P0120)
P2032 M16/6r1 (throttle valve practical
potentiometer)(P0120)
P2032 transmission control 1 EGS fault 1
P2032 transmission control 1 EGS fault 2
P2032 transmission control 1 EGS fault 3
P2032 transmission control 1 EGS fault 4
P2032 transmission control 1 EGS fault 5
P2032 transmission control 1 EGS fault 6
P2032 transmission control 1 EGS fault 7
P2032 transmission control 1 EGS fault 8
P2032-001 EGR,very slight leak [P0456]
P2032-002 EGR,slight leak [P0442]
P2032-004 EGR,severe leak [P0455]
P2032-008 EGR,fuel tank cover lose (idle
error identified).[P0457]
P2032-016 EGR,fuel tank cover lose (driving
error identified).[P0457]
P2033 S40/4 (CC switch with variable
speed limiter)
P2033 S40/4 (TPM touch switch with
variable speed limit)
P2033 transmission control 2 EGS fault 1
P2033 transmission control 2 EGS fault 2
P2033 transmission control 2 EGS fault 3
P2033 transmission control 2 EGS fault 4
P2033 transmission control 2 EGS fault 5
P2033 transmission control 2 EGS fault 6
P2033 transmission control 2 EGS fault 7
P2033 transmission control 2 EGS fault 8
P2033-001 Y58/4 (canister cut-off valve),positive
short [P0448]
P2033-002 Y58/4 (canister cut-off valve),overload
short [P0448]
P2033-004 Y58/4 (canister cut-off valve),wire
open [P0447]
P2033-008 Y58/4 (canister cut-off valve),valve
stick conditionff
[P0446]
P2034 check SRS system.Air bag signal
short after UB
P2034 check SRS system.Air bag signal
will cause the engine stop.
P2034 L5 (crankshaft position
sensor)(P0335)
P2034 L5 (Crankshaft position
sensor)(P0335)
P2034-001 speed meter interrupt,throttle
valve malfunction
P2034-002 speed meter interrupt,brake
light switch malfunction
P2034-004 speed meter interrupt,touch
switch error
P2034-008 speed meter interrupt,brake
light switch CAN BUS signal error
P2035 check M4/7 (electric inspiration
motor and integrated A/C).Circuit open
P2035 check M4/7 (electric inspiration
motor and integrated A/C).Short to
ground
P2035 check M4/7 (electric inspiration
motor and integrated A/C).Short
P2035 M4/7 (electric inspiration motor
and integrated A/C) regulator fault (via
ground key).
P2035-001 N3/10 (ME controller),malfunction
[P0221]
P2035-002 N3/10 (ME controller),malfunction
[P0221]
P2035-004 N3/10 (ME controller),malfunction
[P0221]
P2035-008 N3/10 (ME controller),malfunction
[P0221]
P2035-016 N3/10 (ME controller),malfunction
[P0226]
P2035-032 N3/10 (ME controller),malfunction
[P0226]
P2035-064 N3/10 (ME controller),malfunction
[P0226]
P2035-128 N3/10 (ME controller),malfunction
[P0221]
P2036 check N33/2 (heat controller)
producer.
P2036 N33/2 (heat controller) circuit
open
P2036 N33/2 (heat controller) regulator
fault (via ground key).
P2036 N33/2 (heat controller) short to
ground
P2036 N33/2 (heat controller) short
P2036 No or incorrect CAN message from
control unit N47-5 (ESP control
module)(P0600)
P2036 no signal or error signal from
N47-5 (ESP controller) controller BUS
(P0600)
P2036-001 intake air device:wrong
operation (work link),air flow too small.[P0410]
P2037 check radiator shutter/engine
mount.Engine mount circuit open
P2037 check radiator shutter/engine
mount.Engine mount regulator fault (via
ground key)
P2037 check radiator shutter/engine
mount.Engine mount short to ground
P2037 check radiator shutter/engine
mount.Radiator shutter circuit open
P2037 check radiator shutter/engine
mount.Radiator shutter regulator fault
(via ground key).
P2037 check radiator shutter/engine
mount.Radiator shutter short to ground
P2037 No or incorrect CAN message from
control unit N15/3 (ETC control
module)(P0600)
P2037 no signal or error signal from
N15/3 (EGS controller) controller BUS
(P0600)
P2037-001 B4/3 (fuel tank pressure
sensor),overload short [P0452]
P2037-002 B4/3 (fuel tank pressure
sensor),positive short/wire open [P0453]
P2037-004 B4/3 (fuel tank pressure
sensor),signal reliability malfunction/fuel
tank cover lose.[P0451]
P2037-008 B4/3 (fuel tank pressure
sensor),signal reliability malfunction
[P0451]
P2038 A16/2 (knock sensor 2,left)
P2038 check M44 (booster air cooler
circulation pump).Circuit open
P2038 check M44 (booster air cooler
circulation pump).Short to ground
P2038 check M44 (booster air cooler
circulation pump).Short
P2038-001 charging pressure too
low.[P0243]
P2038-002 charging pressure too
high.[P0243]
P2039 CAN-fault,fault 1
P2039 CAN-fault,fault 2
P2039 check CAN.CAN signal from
controller N51/2 (controller ABC) (airmatic)
error or interfered
P2039 check CAN.CAN-data bus open
P2039 check CAN.CAN-signal from A1
(instrument cluster) error
P2039 check CAN.CAN-signal N15/5 (electronic
shift lever module controller) error
P2039 component B40 (oil condition,temperature
and quality)oil condition error
P2039 Component B40 (Oil sensor (oil
level,temperature and quality))oil level
implausible
P2039-001 M16/7 (air exchange valve
adjustment part),not initialization
[P0243]
P2039-002 M16/7 (air exchange valve
adjustment part),urgency start position
[P0243]
P2039-004 M16/7 (air exchange valve
adjustment part),urgency start
regulation
P203A insufficient fuel (P0460)
P203A The fuel tank level is too
low.(P0460)
P203A-001 M16/7 (air exchange valve
adjustment part),practical potentiometer
1 signal voltage too high.[P0246]
P203A-002 M16/7 (air exchange valve
adjustment part),practical potentiometer
1 signal voltage too low.[P0245]
P203A-004 M16/7 (air exchange valve
adjustment part),practical potentiometer
2 signal voltage too high.[P0246]
P203A-008 M16/7 (air exchange valve
adjustment part),practical potentiometer
2 signal voltage too low.[P0245]
P203A-016 M16/7 (air exchange valve
adjustment part),practical potentiometer
comparison error [P0244]
P203A-032 M16/7 (air exchange valve
adjustment part),air exchange valve
stick.[P0244]
P203A-064 M16/7 (air exchange valve
adjustment part),urgency start position
not reach
P203A-128 M16/7 (air exchange valve
adjustment part),drive servo motor
[P0244]
P203B electronic accelerograph action
inspection component malfunction (P0221)
P203B Fault of function monitor in
electronic accelerator (P0221)
P203B-001 G3/1 (O2 sensor after CAT),overload
short [P0137]
P203B-002 G3/1 (O2 sensor after CAT),positive
short [P0138]
P203B-004 G3/1 (O2 sensor after CAT),interrupt
[P0136]
P203B-008 G3/1 (O2 sensor after
CAT),draw off sensor error [P0136]
P203B-016 G3/1 (O2 sensor after CAT),'aging'
signal error [P0140]
P203C Fault of priority 1:fault of
function monitor in electronic
accelerator (P0221)
P203C priority 1 error:electronic
accelerograph action inspection
component malfunction (P0221)
P203C-001 engine RPM signal,error
P203C-002 engine RPM signal,positive
short
P203C-004 engine RPM signal,overload
short
P203D Angle variation of camshaft to
crankshaft (P0370)
P203D rotate angle error between right
cylinder bank camshaft and crankshaft
(P0370)
P203D-001 N15/6 (automatic shift
transmission controller) urgency
start,controller N15/6 (automatic shift
transmission controller) requested power
P203D-002 N15/6 (automatic shift
transmission controller) urgency
start,controller N15/6 (automatic shift
transmission controller) requested power
P203D-004 N15/6 (automatic shift
transmission controller) urgency
start,controller N15/6 (automatic shift
transmission controller) requested power
P203E BUS signal error from combination
instrument (P0600)
P203E No CAN message from instrument
cluster or message faulty.(P0600)
P203E-001 speed auto control,electronic
accelerograph pedal urgency start
P203E-002 speed auto control,speed meter
switch position error
P203F-001 N3/10 (ME controller),error
[P0221]
P203F-002 N3/10 (ME controller),engine
traction torque [P0221]
P203F-004 CAN BUS error (ESP,EGS,EIS)
P203F-008 N3/10 (ME controller),error
P2040 check anti-theft lock.Controller
N3/9 (controller CDI) and controller N73
(controller EIS) disaccord.
P2040 check anti-theft lock.EEPROM fault.
P2040 check anti-theft lock.No signal
from component N73 (controller EIS)
P2040 component B40 (engine oil sensor
(engine oil condition,temperature and
quality))oil quality error
P2040 Component B40 (Oil sensor (oil
level,temperature and quality))oil
quality implausible
P2040-001 signal from EWM controller CAN
BUS,CAN BUS interrupt
P2041 check N73 (controller EIS).Fault
1
P2041 check N73 (controller EIS).Fault 2
P2041 check N73 (controller EIS).Fault 3
P2041 check N73 (controller EIS).Fault 4
P2041 check N73 (controller EIS).Signal
error EIS
P2041 check N73 (controller EIS).Signal
error N80 (sleeve module)
P2041 component B40 (engine oil sensor
(engine oil condition,temperature and
quality)):water in engine oil
P2041 Component B40 (Oil sensor (oil
level,temperature and quality)):Water in
engine oil
P2041-001 N3/10 (ME
controller),controller EEPROM error
[P0605]
P2041-002 N3/10 (ME controller),internal
error [P0606]
P2041-004 N3/10 (ME controller),communication
error [P0606]
P2042 check B37 (accelerator pedal
position sensor).Sensor 1 signal voltage
too high.
P2042 check B37 (accelerator pedal
position sensor).Sensor 1 signal voltage
too low.
P2042 check B37 (accelerator pedal
position sensor).Sensor 1/2 reliability
P2042 check B37 (accelerator pedal
position sensor).Sensor 2 signal voltage
too high.
P2042 check B37 (accelerator pedal
position sensor).Sensor 2 signal voltage
too low.
P2042 check B37 (accelerator pedal
position sensor).Sensor voltage supply
P2042 fuel safety cut-off unit
recognized
P2042 Safety fuel shutoff detected
P2042-001 M16/6 (throttle valve
regulation part),practical potentiometer
1 and 2:signal voltage error or
regulation malfunction [P0120]
P2043 large external interference from
EGS.Cannot receive all CAN information.
P2043 large external interference from
EGS.CAN-signal implausible.
P2043 large external interference from
EGS.No CAN-communication with component
EGS
P2043 large external interference from
EGS.Request information of controller
EGS implausible.
P2043 misfire (P0300)
P2043 Misfiring (P0300)
P2044 cylinder 1 misfire (P0301)
P2044 large external interference from
ESP.Cannot receive all CAN information.
P2044 large external interference from
ESP.CAN-signal implausible.
P2044 large external interference from
ESP.No communication
P2044 large external interference from
ESP.Request of controller DTR
implausible.
P2044 large external interference from
ESP.Signal error
P2044 Misfiring of cylinder 1 (P0301)
P2045 cylinder 5 misfire (P0305)
P2045 large external interference from
controller DTR.Cannot receive all CAN
information.
P2045 large external interference from
controller DTR.CAN-signal implausible.
P2045 large external interference from
controller DTR.No communication
P2045 large external interference from
controller DTR.Request of controller DTR
implausible.
P2045 Misfiring of cylinder 5 (P0305)
P2046 brake CAN-signal implausible.
P2046 check brake.Cannot receive all CAN
information.
P2046 check brake.Signal error
P2046 cylinder 3 misfire (P0303)
P2046 Misfiring of cylinder 4 (P0304)
P2047 A/C fault 1
P2047 A/C fault 2
P2047 cylinder 6 misfire (P0306)
P2047 Misfiring of cylinder 2 (P0302)
P2048 cylinder 2 misfire (P0302)
P2048 Misfiring of cylinder 6 (P0306)
P2049 cylinder 4 misfire (P0304)
P2049 Misfiring of cylinder 3 (P0303)
P204A cylinder 7 misfire (P0307)
P204A Misfiring of cylinder 7 (P0307)
P204B cylinder 11 misfire (P0311)
P204B Misfiring of cylinder 8 (P0308)
P204C cylinder 9 misfire (P0309)
P204D cylinder 12 misfire (P0312)
P204E cylinder 8 misfire (P0308)
P204F cylinder 10 misfire (P0310)
P2050 interrupt,CAT damageed (P0300)
P2050 Misfiring,Damages TWC (P0300)
P2051 cylinder 1 misfire,CAT damageed
(P0301)
P2051 Misfiring of cylinder 1,damages
TWC (P0301)
P2052 cylinder 5 misfire,CAT damageed
(P0305)
P2052 Misfiring of cylinder 5,damages
TWC (P0305)
P2053 cylinder 3 misfire,CAT damageed
(P0303)
P2053 Misfiring of cylinder 4,damages
TWC (P0304)
P2054 cylinder 6 misfire,CAT damageed
(P0306)
P2054 Misfiring of cylinder 2,damages
TWC (P0302)
P2055 cylinder 2 misfire,CAT damageed
(P0302)
P2055 Misfiring of cylinder 6,damages
TWC (P0306)
P2056 cylinder 4 misfire,CAT damageed
(P0304)
P2056 Misfiring of cylinder 3,damages
TWC (P0303)
P2057 cylinder 7 misfire,CAT damageed
(P0307)
P2057 Misfiring of cylinder 7,damages
TWC (P0307)
P2058 cylinder 11 misfire,CAT damageed
(P0311)
P2058 Misfiring of cylinder 8,damages
TWC (P0308)
P2059 cylinder 9 misfire,CAT damageed
(P0309)
P205A cylinder 12 misfire,CAT damageed
(P0312)
P205B cylinder 8 misfire,CAT damageed
(P0308)
P205C cylinder 10 misfire,CAT damageed
(P0310)
P205E Component N15/3 (ETC control
module) memory is fault.(P0702)
P205E fault stored in component N15/3 (EGS
controller).(P0702)
P205F Component N15/3 (ETC control
module) memory is fault.(P0753)
P205F fault stored in component N15/3 (EGS
controller).(P0753)
P2060 Component N15/3 (ETC control
module) memory is fault.(P0758)
P2060 fault stored in component N15/3 (EGS
controller).(P0758)
P2061 Component N15/3 (ETC control
module) memory is fault.(P0763)
P2061 fault stored in component N15/3 (EGS
controller).(P0763)
P2062 Component N15/3 (ETC control
module) memory is fault.(P0743)
P2062 fault stored in component N15/3 (EGS
controller).(P0743)
P2063 Component N15/3 (ETC control
module) memory is fault.(P0748)
P2063 fault stored in component N15/3 (EGS
controller).(P0748)
P2064 Component N15/3 (ETC control
module) memory is fault.(P0748)
P2064 fault stored in component N15/3 (EGS
controller).(P0748)
P2065 Component N15/3 (ETC control
module) memory is fault.(P0702)
P2065 fault stored in component N15/3 (EGS
controller).(P0702)
P2066 Component N15/3 (ETC control
module) memory is fault.(P0715)
P2066 fault stored in component N15/3 (EGS
controller).(P0715)
P2067 Component N15/3 (ETC control
module) memory is fault.(P0705)
P2067 fault stored in component N15/3 (EGS
controller).(P0705)
P2068 Component N15/3 (ETC control
module) memory is fault.(P0720)
P2068 fault stored in component N15/3 (EGS
controller).(P0720)
P2069 Component N15/3 (ETC control
module) memory is fault.(P0700)
P2069 fault stored in component N15/3 (EGS
controller).(P0700)
P206A Component N15/3 (ETC control
module) memory is fault.(P0700)
P206A fault stored in component N15/3 (EGS
controller).(P0700)
P206B Component N15/3 (ETC control
module) memory is fault.(P0740)
P206B fault stored in component N15/3 (EGS
controller).(P0740)
P206D Component N15/3 (ETC control
module) memory is fault.(P0730)
P206D fault stored in component N15/3 (EGS
controller).(P0730)
P206E Control module ME-SFI 2.8 is
incorrectly coded (coded to MT,vehicle
has AT)
P206E ME 2.7 controller incorrect coded
(according to AT code,car has MT)
P206F Control module ME-SFI 2.8 is
incorrectly coded or there is fault in
the CAN communication with control
module N15/3 (ETC control module)
P206F ME 2.7 controller incorrectly
coded or communication error with N15/3
(EGS controller) controller BUS
P2070 as component N15/3 (EGS
controller) voltage is too low,transmission
variables can not be checked
P2070 Transmission version cannot be
checked because of undervoltage at
component N15/3 (ETC control module)
P2071 Start enable of DAS not sent
P2072 B4/3 (fuel tank pressure sensor),signal
error (P0450)
P2072 B4/3 (Fuel tank pressure sensor),Signal
implausible (P0450)
P2073 Electric suction fan for engine or
air conditioning
P2073 M4/3 (engine/A/C electronic
suction device)
P2074 Y22/6 (variable intake manifold
switchover valve)
P2075 EGR slight leak (leakage)(P0442)
P2075 Pruge control system has a slight
leak (minor leak)(P0442)
P2076 Component B40 (Oil sensor (oil
level,temperature and quality))il
temperature implausible
P2077 Read fault memory from control
unit N15/6 (Sprintshift control module)
and rectify faults.
P2078 Read fault memory from control
unit N15/6 (Sprintshift control module)
and rectify faults.
P2079 CAN signal 'Vehicle speed limit'
P207A CAN signal 'Vehicle speed limit'
P207B Read fault memory from control
unit Transmission and rectify faults.
P207D No or incorrect CAN message from
control unit N73 (EIS control module)
P207D no signal or error signal from N73
(EIS controller) controller BUS
P207E cylinder 4-6 CAT too weak (P0422)
P207E The efficiency of the left
catalytic converter is insufficient.(P0432)
P207F G3/10 (right O2 sensor,before CAT,cylinder
4-6) aging,calibration program jump over
(P0133)
P207F G3/3 (Left O2 sensor,before TWC[KAT])
Aging,correction variable exceeded
P2080 G3/10 (right O2 sensor,before CAT,cylinder
4-6) aging,used too long (P0133)
P2080 G3/3 (Left O2 sensor,before TWC[KAT])
Aging,period too long (P0153)
P2081 G3/14 (right O2 sensor,after CAT,cylinder
4-6) no special condition change
P2081 G3/5 (Left O2 sensor,after TWC[KAT])
P2082 G3/10 (right O2 sensor,before CAT,cylinder
4-6) aging,voltage up too small (P0130)
P2082 G3/3 (Left O2 sensor,before TWC[KAT])
Electrical fault (P0150)
P2083 G3/14 (right O2 sensor,after CAT,cylinder
4-6) electrical malfunction (P0136)
P2083 G3/5 (Left O2 sensor,after TWC[KAT])
Electrical fault (P0156)
P2085 cylinder 4-6 mixture formation
unit adaptation reaches limit.(part load)(P0170)
P2085 Self-adaptation of mixture
formation for left bank of cylinders is
at limit value (at part load).(P0173)
P2086 cylinder 4-6 mixture formation
unit adaptation reaches limit.(idle)(P0170)
P2086 Self-adaptation of mixture
formation for left bank of cylinders is
at limit value (at idle speed).(P0173)
P2087 cylinder 4-6 mixture formation
unit adaptation reaches limit.(between
idle and part load)
P2087 Self-adaptation of mixture
formation for left bank of cylinders is
at limit value (between idle speed and
part load).(P0173)
P2088 component G3/10 (right O2 sensor,before
CAT,cylinder 4-6) heating (P0135)
P2088 Heating of component G3/3 (Left O2
sensor,before TWC[KAT])(P0155)
P2089 component G3/14 (right O2 sensor,after
CAT,cylinder 4-6) heating (P0141)
P2089 Heating of component G3/5 (Left O2
sensor,after TWC[KAT])(P0161)
P208A Y62y7 (Fuel injector cylinder
7)(P0207)
P208B Y62y11 (cylinder 11 fuel
injector)(P0211)
P208B Y62y8 (Fuel injector cylinder
8)(P0208)
P208C Y49/1 (camshaft regulation valve,left
cylinder bank),electrical malfunction
(P0340)
P208E Y81 (cylinder cut-off valve,left
cylinder bank),electrical malfunction;GERMANY
P208E Y81/1 (10-cylinder 12 cylinder
cut-off valve),electrical malfunction
P208F Y81/1 (10-cylinder 12 cylinder
cut-off valve),electrical malfunction
P2090 at least two socket of O2 sensor
exchanged.
P2090 Plug connections of the O2 sensors
are wrongly connected.(O2 sensor
upstream TWC)
P2091 B40/2 (cylinder disable unit oil
pressure sensor),electrical malfunction
(P0520)
P2091 B40/2 (cylinder off oil pressure
sensor),electrical malfunction (P0520);GERMANY
P2092 Y80/1 (cylinder 7-9 cylinder
cut-off valve),electrical malfunction
P2093 Y80 (cylinder cut-off valve,right
cylinder bank),electrical malfunction;GERMANY
P2093 Y80/1 (cylinder 7-9 cylinder
cut-off valve),electrical malfunction
P2094 when ZAS is turned on,left and
right cylinder cut-off valve (Y80 or
Y81) is not opened.;
P2095 when ZAS is turned on,cylinder
inlet valve does not work.;
P2097 throttle valve block (ice up)
P2097 throttle valve block (ice up);
P2098 component N2/7 (SRS controller)
crash signal error.;
P2098 error crash signal from component
N2/7 (SRS controller)
P2099 when ZAS is turned off,cylinder 8
exhaust valve inactive.
P209A when ZAS is turned off,cylinder 10
exhaust valve inactive.
P209B Y93 (EGR switch-over valve)
P209B Y93 (EGR switch-over valve);
P209C when ZAS is turned off,component
Y80 (cylinder cut-off valve,right
cylinder bank) not turn off.;
P209C when ZAS is turned off,component
Y80/1 (cylinder 7-9 cylinder cut-off
valve) not off.
P209D when ZAS is turned off,component
Y81 (cylinder cut-off valve,left
cylinder bank) not turn off.;
P209D when ZAS is turned off,component
Y81/1 (cylinder 10-12 cylinder cut-off
valve) not off.
P209E when ZAS is turned off,cylinder 5
exhaust valve not work.;
P209E when ZAS is turned off,cylinder 7
exhaust valve inactive.
P209F when ZAS is turned off,cylinder 11
exhaust valve inactive.
P209F when ZAS is turned off,cylinder 2
exhaust valve not work.;
P20A0 when ZAS is turned off,cylinder 3
exhaust valve not work.;GERMANY
P20A0 when ZAS is turned off,cylinder 9
exhaust valve inactive.
P20A1 when ZAS is turned off,cylinder 12
exhaust valve inactive.
P20A1 when ZAS is turned off,cylinder 8
exhaust valve not work.;GERMANY
P20A2 when ZAS is turned off,intake
valve of some cylinder inactive.
P20A2 when ZAS is turned off,some
cylinder exhaust valve not work.;GERMANY
P20A3 7-9 cylinder CAT too weak.(P0432)
P20A4 10-12 cylinder CAT too weak.(P0432)
P20A5 G3/7 (left O2 sensor,before CAT,cylinder
7-9):aging,calibration program jump over
(P0153)
P20A6 G3/8 (left O2 sensor,before CAT,cylinder
10-12):aging,calibration program jump
over (P0153)
P20A7 G3/7 (left O2 sensor,before CAT,cylinder
7-9):aging,used too long (P0153)
P20A8 G3/8 (left O2 sensor,before CAT,cylinder
10-12):aging,used too long (P0153)
P20A9 G3/7 (left O2 sensor,before CAT,cylinder
7-9),electrical malfunction (P0150)
P20AA G3/8 (left O2 sensor,before CAT,cylinder
10-12),electrical malfunction (P0150)
P20AB G3/11 (left O2 sensor,after CAT,cylinder
7-9),electrical malfunction (P0156)
P20AC G3/12 (left O2 sensor,after CAT,cylinder
10-12),electrical malfunction (P0156)
P20AD cylinder 7-9 mixture formation
unit adaptation reaches limit.(part load)(P0173)
P20AE 10-cylinder 12 mixture formation
unit adaptation reaches limit.(part load)(P0173)
P20AF cylinder 7-9 mixture formation
unit adaptation reaches limit.(idle)(P0173)
P20B0 cylinder 10-12 mixture formation
unit adaptation reaches limit.(idle)(P0173)
P20B1 cylinder 7-9 mixture formation
unit adaptation reaches limit.(between
idle and part load)
P20B2 cylinder 10-12 mixture formation
unit adaptation reaches limit.(between
idle and part load)
P20B3 component G3/7 (left O2 sensor,before
CAT,cylinder 7-9) heating (P0155)
P20B4 component G3/8 (left O2 sensor,before
CAT,cylinder 10-12) heating (P0155)
P20B5 component G3/11 (left O2 sensor,after
CAT,cylinder 7-9) heating (P0161)
P20B6 component G3/12 (left O2 sensor,after
CAT,cylinder 10-12) heating (P0161)
P20B7 Increased idle speed due to SBC
low-voltage:Check current and voltage on
vehicle./No control module defective
(P1999.183)
P20B8 B6/2 (camshaft Hall sensor,left
cylinder bank)(P0340)
P20B9 Y62y9 (cylinder 9 fuel
injector)(P0209)
P20BA Y62y12 (cylinder 12 fuel
injector)(P0212)
P20BB Y62y8 (cylinder 8 fuel
injector)(P0208)
P20BC Y62y10 (cylinder 10 fuel
injector)(P0210)
P20BD rotate angle error between left
cylinder bank camshaft and crankshaft
(P0378)
P20BE component G3/9 (right O2 sensor,before
CAT,cylinder 1-3) heating,supply voltage
(P0135)
P20BE Heating of component G3/4 (Right
O2 sensor,before TWC[KAT]),Voltage
supply (P0135)
P20BF component G3/10 (right O2 sensor,before
CAT,cylinder 4-6) heating,supply voltage
(P0135)
P20BF Heating of component G3/3 (Left O2
sensor,befor TWC[KAT]),Voltage supply
(P0135)
P20C0 component G3/7 (left O2 sensor,before
CAT,cylinder 7-9) heating,supply voltage
(P0155)
P20C1 component G3/8 (left O2 sensor,before
CAT,cylinder 10-12) heating,supply
voltage (P0155)
P20C2 component G3/13 (right O2 sensor,after
CAT,cylinder 1-3) heating,supply voltage
(P0141)
P20C2 Heating of component G3/6 (Right
O2 sensor,after TWC[KAT]),Voltage supply
(P0141)
P20C3 component G3/14 (right O2 sensor,after
CAT,cylinder 4-6) heating,supply voltage
(P0141)
P20C3 Heating of component G3/5 (Left O2
sensor,after TWC[KAT]),Voltage supply
(P0141)
P20C4 component G3/11 (left O2 sensor,after
CAT,cylinder 7-9) heating,supply voltage
(P0161)
P20C5 component G3/12 (left O2 sensor,after
CAT,cylinder 10-12) heating,supply
voltage (P0161)
P20C6 G3/11 (left O2 sensor,after CAT,cylinder
7-9),no special condition change
P20C7 G3/12 (left O2 sensor,after CAT,cylinder
10-12),no special condition change
P20C8 Y32/1 (air pump conversion switch,left
cylinder bank)(P0415)
P20C9 left cylinder bank intake unit
error operation (work link)(P0410)
P20CA No CAN message 'Vehicle speed
signal left rear wheel' from control
module N47-5 (ESP control module) or
message faulty.(P0500)
P20CA no RL wheel speed signal or error
signal from N47-5 (electronic stable
program controller) controller BUS
(P0500)
P20CB No CAN message 'Vehicle speed
signal left front wheel' from control
module N47-5 (ESP control module) or
message faulty.(P0500)
P20CB no FL wheel speed signal or error
signal from N47-5 (electronic stable
program controller) controller BUS
(P0500)
P20CC 'Rough road detection' signal (by
comparing wheel speeds)
P20CD A/C compressor torque error
P20CD AC compressor torque implausible
P20CE A/C refrigerant pressure too high
P20CE Refrigerant pressure in air
conditioning too high
P20CF component B37 (pedal position
sensor) voltage difference error between
signal 1 and signal 2 (P0120)
P20CF The voltage difference between
signal 1 and signal 2 of component B37 (Pedal
value sensor) is implausible.(P0120)
P20D0 A/C request an error ventilation
efficiency.
P20D0 The air conditioning requests an
implausible fan output.
P20D1 The torque request from control
module N63/1 (DTR control module) is
implausible.
P20D1 torque request error from N63/1 (DTR
controller) controller.
P20D2 CAN transmission error of torque
request from control module N63/1 (DTR
control module)
P20D2 controller N63/1 (DTR controller)
torque request BUS transmission error
P20D3 CAN transmission error of torque
request from control module N63/1 (DTR
control module)
P20D3 controller N63/1 (DTR controller)
torque request BUS transmission error
P20D4 load limit valid.
P20D4 The load limit is active.
P20D5 controller N15/3 (EGS controller)
torque request error.(P0702)
P20D5 The torque request from control
module N15/3 (ETC control module) is
implausible.(P0702)
P20D6 CAN transmission error of torque
request from control module N15/3 (ETC
control module)(P0702)
P20D6 controller N15/3 (EGS controller)
torque request BUS transmission error
(P0702)
P20D7 CAN transmission error of torque
request from control module N15/3 (ETC
control module)(P0702)
P20D7 controller N15/3 (EGS controller)
torque request BUS transmission error
(P0702)
P20D8 electronic stable program
malfunction
P20D8 ESP fault
P20D9 controller N47-5 (ESP controller)
torque request error.
P20D9 The torque request from control
module N47-5 (ESP control module) is
implausible.
P20DA CAN transmission error of torque
request from control module N47-5 (ESP
control module)
P20DA controller N47-5 (ESP controller)
torque request BUS transmission error
P20DB CAN transmission error of torque
request from control module N47-5 (ESP
control module)
P20DB controller N47-5 (ESP controller)
torque request BUS transmission error
P20DC B37 (pedal position sensor),signal
channel 1 open(P0120)
P20DC B37 (Pedal value sensor),Open
circuit at signal path 1 (P0120)
P20DD B37 (pedal position sensor),signal
channel 1 short(P0120)
P20DD B37 (Pedal value sensor),Short
circuit at signal path 1 (P0120)
P20DE B37 (pedal position sensor),signal
channel 2 open(P0120)
P20DE B37 (Pedal value sensor),Open
circuit at signal path 2 (P0120)
P20DF B37 (pedal position sensor),signal
channel 2 short(P0120)
P20DF B37 (Pedal value sensor),Short
circuit at signal path 2 (P0120)
P20E0 Ignore fault code and erase fault
memory.
P20E0 software error,memory clear error.
P20E1 Ignore fault code and erase fault
memory.
P20E1 software error,memory clear error.
P20E2 Ignore fault code and erase fault
memory.
P20E2 software error,memory clear error.
P20E3 component B37 (pedal position
sensor) supply voltage (P0120)
P20E3 Voltage supply of component B37 (Pedal
value sensor)(P0120)
P20E4 error signal from component S9/1 (brake
light switch)
P20E4 Implausible signal from component
S9/1 (Stop lamp switch)
P20E5 CAN transmission error of signal
from component S9/1 (Stop lamp switch)
P20E5 component S9/1 (brake light
switch) signal BUS transmission error
P20E6 CAN transmission error of signal
from component S9/1 (Stop lamp switch)
P20E6 component S9/1 (brake light
switch) signal BUS transmission error
P20E7 cylinder 1 ion current signal lose
or error.(P0301)
P20E8 cylinder 2 ion current signal lose
or error.(P0302)
P20E9 cylinder 3 ion current signal lose
or error.(P0303)
P20EA cylinder 4 ion current signal lose
or error.(P0304)
P20EB cylinder 5 ion current signal lose
or error.(P0305)
P20EC cylinder 6 ion current signal lose
or error.(P0306)
P20ED cylinder 1 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/1)
P20EE cylinder 2 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/1)
P20EF cylinder 3 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/1)
P20F0 cylinder 4 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/1)
P20F1 cylinder 5 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/1)
P20F2 cylinder 6 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/1)
P20F3 cylinder 7 ion current signal lose
or error.(P0307)
P20F4 cylinder 8 ion current signal lose
or error.(P0308)
P20F5 cylinder 9 ion current signal lose
or error.(P0309)
P20F6 cylinder 10 ion current signal
lose or error.(P0310)
P20F7 cylinder 11 ion current signal
lose or error.(P0311)
P20F8 cylinder 12 ion current signal
lose or error.(P0312)
P20F9 cylinder 7 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/2)
P20FA cylinder 8 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/2)
P20FB cylinder 9 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/2)
P20FC cylinder 10 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/2)
P20FD cylinder 11 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/2)
P20FE cylinder 12 spark plug a,b or
ignition mode ECI,right cylinder bank
(N92/2)
P2100 Component Y3/6y3 (1-2 and 4-5
shift solenoid valve) is faulty.
P2100 The internal electrical check of
component Y3/6y3(1-2 and 4-5 shift
solenoid valve) has failed.
P2101 Component Y3/6y3(1-2 and 4-5 shift
solenoid valve) has a short circuit to
ground.
P2102 Component Y3/6y5 (2-3 shift
solenoid valve) is faulty.
P2102 The internal electrical check of
Component Y3/6y5(2-3 shift solenoid
valve) has failed.
P2103 Component Y3/6y5(2-3 shift
solenoid valve) has a short circuit to
ground.
P2104 Component Y3/6y4 (3-4 shift
solenoid valve) is faulty.
P2104 The internal electrical check of
Component Y3/6y4(3-4 shift solenoid
valve) has failed.
P2105 Component Y3/6y4(3-4 shift
solenoid valve) has a short circuit to
ground.
P2106 Component Y3/6y6 (Torque converter
lockup PWM solenoid valve) is faulty.
P2106 The internal electrical check of
Component Y3/6y6(Torque converter lockup
PWM solenoid valve) has failed.
P2107 Component Y3/6y1 (Modulating
pressure control solenoid valve) is
faulty.
P2107 The internal electrical check of
Component Y3/6y1(Modulating pressure
control solenoid valve) has failed.
P2108 Component Y3/6y2 (Shift pressure
control solenoid valve) is faulty.
P2108 The internal electrical check of
Component Y3/6y2(Shift pressure control
solenoid valve) has failed.
P2109 Component Y66/1(Reversing and
parking lock solenoid) has short circuit
or no connection.
P210A The cable to component
K38/3(Starter lockout relay) has short
circuit or no connection.
P2193 Injector classification
Plausibility
P2193 Injector classification:Checksum
is incorrect.
P2193 Injector classification:Invalid
injector class
P2200 Component Y3/6n2(speed sensor
2) is faulty or the sensor supply has
Short circuit.
P2200 Instrument cluster Fault from
instrument cluster over CAN
P2200 Instrument cluster Preglow
indicator lamp faulty
P2201 CAN message from control module
DAS Plausibility 1
P2201 CAN message from control module
DAS Plausibility 2
P2201 CAN message from control module
DAS:CAN signal faulty
P2201 No or incorrect CAN message from
control unit DAS
P2202 External quantity control by DTR
control module Not all CAN messages have
been received.
P2202 External quantity control by DTR
control module Request from control
module N63/1 (DTR control module) is
implausible.
P2202 External quantity control by DTR
control module The CAN message is
implausible
P2202 External quantity control by DTR
control module Torque request from
control module N63/1 (DTR control
module) is faulty.
P2203 Component Y3/6n3 (speed sensor 3)
is faulty.
P2203 External quantity control by ESP
NO COMMUNICATION
P2203 External quantity control by ESP
Not all CAN message have been received.
P2203 External quantity control by ESP
Request from control module ESP is
implausible.1
P2203 External quantity control by ESP
Request from control module ESP is
implausible.2
P2203 External quantity control by ESP
The CAN message is implausible.
P2203 External quantity control by ESP
Torque request from control module ESP
is faulty.
P2203 The internal electrical check of
Component Y3/6n3(speed sensor 3) has
failed.
P2204 External quantity control by ETC
CAN reception timeout
P2204 External quantity control by ETC
ENGINE STOP
P2204 External quantity control by ETC
Not all CAN messages have been received.
P2204 External quantity control by ETC
Read fault memory of control unit N15/3
(ETC control module).
P2204 External quantity control by ETC
Read fault memory of control unit
Transmission control.
P2204 External quantity control by ETC
Request from control module N15/3 (ETC
control module) is implausible.
P2204 External quantity control by ETC
The CAN message is implausible.
P2204 External quantity control by ETC
Torque request from control module N15/3
(ETC control module) is faulty.
P2206 No signal from output speed sensor
P2207 The value of component Y3/6n3
(speed sensor 3) is implausible.
P220A The speed comparison of Y3/6n2 or
Y3/6n3 is implausible.
P220B The speed of Y3/6n2 or Y3/6n3 is
too high.
P2210 Selector lever coding is invalid.
P2211 The selector lever is in an
intermediate position.
P2212 The selector lever position is
implausible.
P2220 Component Y3/6s1(Starter lockout
contact) or component Y3/6b1 (ATF
temperature sensor) is faulty or both.
P2221 The signal of component Y3/6b1 (ATF
temperature sensor) and (or) Y3/6s1
(Starter lockout contact) is implausible.
P2222 The signal of component Y3/6b1 (ATF
temperature sensor) and (or) Y3/6s1
(Starter lockout contact) is implausible.
P2300 CAN communication is faulty.
P2300 CAN communication with other
control units installed in this vehicle
is not possible.
P2301 CAN communication is faulty.
P2301 CAN communication with other
control units installed in this vehicle
is not possible.
P2306 N3/9 (CDI control module) Sensor
supply voltage 2 Readout too large
P2306 N3/9 (CDI control module) Sensor
supply voltage 2 Readout too small
P2310 CAN communication with the
traction system is faulty.
P2310 One or more messages from control
unit N47(Traction systems control
module) are not available on the CAN
bus.
P2311 CAN communication with the engine
system is faulty.
P2311 One or more messages from the
engine control unit are not available on
the CAN bus.
P2312 CAN communication with the engine
system is faulty or engine temperature
is implausible.
P2312 One or more messages from the
engine control unit are not available on
the CAN bus.
P2313 There is a fault in CAN
communication with control module N15/5
(electronic selector lever module
control module) or the selector lever
position of control module ESM is
implausible.
P2314 Fault in CAN communication with
control unit N73 (EIS control module)
P2314 One or more messages from control
unit N73(EIS control module) are not
available on the CAN bus.
P2315 Fault in CAN communication with
control unit A1 (Instrument cluster)
P2315 One or more messages from control
unit A1(Instrument cluster) are not
available on the CAN bus.
P2316 Fault in CAN communication with
control unit A1 (Instrument cluster)
P2316 One or more messages from control
unit N19(Air conditioning control
module) are not available on the CAN
bus.
P2317 One or more messages from control
unit N78(Transfer case control module)
are not available on the CAN bus.
P2317 There is a sporadic fault in CAN
communication with control module N78
(Transfer case control module) or the
transfer case position is sporadically
implausible.
P2318 Fault in CAN communication with
control unit N15/5 (electronic selector
lever module control module)
P2318 One or more messages from control
unit N15/5(electronic selector lever
module control module) are not available
on the CAN bus.
P2319 Analogue-digital converter Dynamic
RAM test is incorrect.
P2319 Analogue-digital converter Ground
keying of pedal value sensor PWG2 is
incorrect.
P2319 Analogue-digital converter Test
voltage is incorrect.
P2330 The CAN signal from traction
system is faulty.
P2330 The CAN signals sent from control
unit N47(Traction systems control
module) are incomplete.
P2331 The CAN signal from the engine
system is faulty.
P2331 The CAN signals sent from control
unit Engine management are incomplete.
P2332 The CAN signal from the engine
system is faulty.
P2332 The CAN signals sent from control
unit Engine management are incomplete.
P2333 The CAN signal from control module
N15/5 (electronic selector module
control module) is faulty.
P2333 The CAN signals sent from control
unit N15/5(electronic selector module
control module) are incomplete.
P2334 The CAN signal from control module
N73 (EIS control module) is faulty.
P2334 The CAN signals sent from control
unit N73(EIS control module) are
incomplete.
P2335 The CAN signal from control module
A1 (Instrument cluster) is faulty.
P2335 The CAN signals sent from control
module A1(Instrument cluster) are
incomplete.
P2336 The CAN signal from control module
N73 (EIS control module) and (or) A1
(Instrument cluster) is faulty.
P2336 The CAN signal from control module
N73(EIS control module) and (or) A1
(Instrument cluster) is faulty.
P2337 The CAN signal from control module
N78 (Transfer case control module) is
faulty.
P2337 The CAN signals sent from control
unit N78(Transfer case control module)
are incomplete.
P2338 The CAN signal from control module
N15/5 (electronic selector lever module
control module) is faulty.
P2338 The CAN signals sent from control
unit N15/5(electronic selector lever
module control module) are incomplete.
P2400 The rear right wheel speed of the
traction system is implausible.
P2400 The right rear wheel rpm signal
sent from the traction system via the
CAN bus is implausible.
P2401 The left rear wheel rpm signal
sent from the traction system via the
CAN bus is implausible.
P2401 The rear left wheel speed of the
traction system is implausible.
P2402 The front right wheel speed of the
traction system is implausible.
P2402 The right front wheel rpm signal
sent from the traction system via the
CAN bus is implausible.
P2403 The front left wheel speed of the
traction system is implausible.
P2403 The left front wheel rpm signal
sent from the traction system via the
CAN bus is implausible.
P2404 The CAN signal from component S9/1
(Stop lamp switch) of the traction
system is implausible.
P2404 The stop lamp switch signal sent
from the traction system via the CAN bus
is implausible.
P2405 The accelerator pedal value of the
engine system is implausible.
P2405 The accelerator pedal value sent
from the engine control unit via the CAN
bus is implausible.
P2406 The engine torque from the engine
system is implausible.
P2406 The specified static torque sent
from the engine control unit via the CAN
bus is implausible.
P2407 The default torque of the traction
system is implausible.
P2407 The engine torque specified by the
traction system and sent from the engine
control unit via the CAN bus is
implausible.
P2408 The engine torque from the engine
system is implausible.
P2408 The maximum engine torque sent
from the engine control unit via the CAN
bus is implausible.
P2409 The engine torque from the engine
system is implausible.
P2409 The maximum engine torque sent
from the engine control unit via the CAN
bus is implausible.
P240A The engine speed of the engine
system is implausible.
P240A The engine speed sent from the
engine control unit via the CAN bus is
implausible.
P240B The engine speed sent from the
engine control unit via the CAN bus is
implausible.
P240B The engine temperature from the
engine system is implausible.
P240C The CAN signal for the selector
lever position from component N15/5
(electronic selector lever module
control module) is implausible.
P240C The selector lever position sent
from control unit N15/5(electronic
selector Lever module control module)via
the CAN bus is implausible.
P240D The current transfer case sent
from control unit N78(Transfer case
control module) via the CAN bus is
implausible.
P240D There is a sporadic fault in CAN
communication with control module N78
(Transfer case control module) or the
transfer case position is sporadically
implausible.
P2500 The transmission has an
impermissible transmission ratio.
P2501 Engine overevving has occurred.
P2502 The gear is implausible or the
transmission is slipping.
P2503 The gear comparison is negative or
the target gear is not reached.
P2510 The torque converter lock-up
clutch causes impermissible closing.
P2511 Engaging of torque converter
lockup clutch not permitted.
P2511 The torque converter lock-up
clutch has excessive power consumption.
P2512 Actuation of torque converter
lockup clutch is not possible
P2520 The feedback through the
transmission protection is not
maintained.
P2600 The voltage supply of circuit 87
has undervoltage.
P2601 The voltage supply of circuit 87
has overvoltage.
P2602 The voltage supply of the valves
is faulty.
P2603 The voltage supply of the speed
sensors is faulty.
